3. Fault Confirmation
__________________
A. Do the operational test of the FADEC 1B on the ground (with engine motoring) (Ref. AMM TASK 73-29-00-710-040).
4. Fault Isolation
_______________
A. If the test gives the maintenance message BSV, J11/J12, ECU:
- do a check for open or short to ground of the harness J11 and J12 between the ECU (4000KS) and the 6 o'clock junction box, between the 6 o'clock junction box and the BSV pins J11 and J12/9, 23, 24 and pins CL11L and CL12L/1, 2 (Ref. ASM 73-25/18) (Ref. AWM 71-51-08).
F 『 EEFF : ALL E ∞∞73-10-00∞∞∞∞∞∞∞∞∞∞Page 239
E E Feb 01/01 ERE ECES
F 『
E C F M E
E E
E 56 E
E E
(1) If the wiring is not correct:
- repair the above defective wiring.
(2) If the wiring is correct:
- disconnect the harness CJ11L and CJ12L from the BSV. Install a jumper wire between the pins 1 and 2 on the harness CJ11L and CJ12L.
- disconnect the connector J11 and J12 from the ECU (4000KS) and do a check of theresistance of the harness J11 and J12 between: . pins 9 and 23 (< 5 Ohms) . pins 9 and 24 (> 10 Megohms) . pin 9 and the ground (> 10 Megohms).
(a) If the resistance values are in the specified limits:
- replace the burner staging valve (BSV) (Ref. AMM TASK 73-11-70-000-002) and (Ref. AMM TASK 73-11-70-400-002).
(b) If the resistance values are out of the specified limits:
- disconnect the harness J11 and J12 from the junction box at the 6 o'clock strut and do a check of the resistance of the harness CJ11L and CJ12L between: for the harness CJ11L . pins 8 and 10 (< 5 Ohms) . pins 8 and 9 (> 10 Megohms) . pin 8 and the ground (> 10 Megohms) for the harness CJ12L . pins 16 and 15 (< 5 Ohms) . pins 16 and 5 (> 10 Megohms) . pin 16 and the ground (> 10 Megohms).
1 If the resistance values are in the specified limits:
_
- replace the harness J11 (Ref. AMM TASK 73-21-50-000-044) and (Ref. AMM TASK 73-21-50-400-044).
- replace the harness J12 (Ref. AMM TASK 73-21-50-000-045) and (Ref. AMM TASK 73-21-50-400-045).
2 If the resistance values are out of the specified limits:
_
- replace the harness CJ11L (Ref. AMM TASK 73-21-50-000-025) and (Ref. AMM TASK 73-21-50-400-025).
- replace the harness CJ12L (Ref. AMM TASK 73-21-50-000-027) and (Ref. AMM TASK 73-21-50-400-027).
(3) If the fault continues:
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
B. Do the test given in Para. 3.A.
F 『R EEFF : ALL E ∞∞73-10-00∞∞∞∞∞∞∞∞∞∞Page 240 E E Feb 01/01 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
TASK 73-10-00-810-832
Feedback Disagree between the Signals of the Two Channels of the BSV on Engine
1. Possible Causes
_______________
- burner staging valve (BSV)
- harness J11
- harness J12
- harness CJ11L
- harness CJ12L
- ECU (4000KS)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 73-11-70-000-002 Removal of the Burner Staging Valve (BSV) AMM 73-11-70-400-002 Installation of the Burner Staging Valve (BSV) AMM 73-21-50-000-025 Removal of the CJ11L Harness AMM 73-21-50-000-027 Removal of the CJ12L Harness AMM 73-21-50-000-044 Removal of the HJ11 Harness AMM 73-21-50-000-045 Removal of the HJ12 Harness AMM 73-21-50-400-025 Installation of the CJ11L Harness AMM 73-21-50-400-027 Installation of the CJ12L Harness AMM 73-21-50-400-044 Installation of the HJ11 Harness AMM 73-21-50-400-045 Installation of the HJ12 Harness AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)(4000KS) AMM 73-21-60-400-001 Installation of the Electronic Control Unit
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發動機燃油和控制 1(51)
