- replace the fuel return valve (Ref. AMM TASK 73-11-50-000-002) and (Ref. AMM TASK 73-11-50-400-002).
2 If the resistance values are in the specified limits:
_
- replace the harness J8 (Ref. AMM TASK 73-21-50-000-041) and (Ref. AMM TASK 73-21-50-400-041).
B. Do the test given in Para. 3.A.
F 『 EEFF : ALL E ∞∞73-20-00∞∞∞∞∞∞∞∞∞∞Page A226
E E Aug 01/05 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
TASK 73-20-00-810-913
Loss of all Engine 1 Identification Connector Data
1. Possible Causes
_______________
- J14 engine identification connector
- ECU1 (4000KS)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU) AMM 73-21-60-400-001 Installation of the Electronic Control Unit (ECU) AMM 73-21-60-740-006 Read the LRU Identification Report and the Thrust
Reverser Shut-off Valve Status AMM 73-21-90-000-002 Removal of the Engine Identification Connector AMM 73-21-90-400-002 Installation of the Engine Identification Connector AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with
Engine non Motoring)
3. Fault Confirmation
__________________
A. Test
(1) Do the operational test of the FADEC 1A on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
(2) Do the LRU identification through the MCDU (Ref. AMM TASK 73-21-60-740-006) and check that the data corresponds to the engine configuration.
4. Fault Isolation
_______________
A. If the test gives the maintenance message J14, ECU (ENG IDENT):
- do a check for the loose or missing identification connector at the ECU1 connector J14 receptacle.
(1) If the Service Bulletin 72-0340 is not incorporated, and if the fault continues:
- reset the ECU1 (4000KS) as follows:
(a) On the panel 115VU, set the ENG/MASTER 1 control switch (3KC) to OFF.
F 『R EEFF : ALL E ∞∞73-20-00∞∞∞∞∞∞∞∞∞∞Page A227 E E Aug 01/05 E E ECES
E E 56 E E E
F 『
E C F M E
E E
(b) After 30 seconds, set the ENG/MASTER 1 control switch (3KC) to ON.
1 If the fault continues:
_
- replace the J14 engine identification connector (Ref. AMM TASK 73-21-90-000-002) and (Ref. AMM TASK 73-21-90-400-002).
a If the fault continues:
_
- replace the ECU1 (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
(2) If the Service Bulletin 72-0340 is incorporated, and if the fault continues:
- read the LRU IDENTIFICATION report of the engine 1 (Ref. AMM TASK 73-21-60-740-006),
- check that the engine identification connector installed on the engine meets the specific engine configuration (rating, N1 trim, system configuration, etc...).
(a) If the rating identified on the LRU IDENTIFICATION report is incorrect:
- replace the J14 engine identification connector (Ref. AMM TASK 73-21-90-000-002) and (Ref. AMM TASK 73-21-90-400-002).
(b) If other parameters than the rating identified on the LRU IDENTIFICATION report is (are) incorrect:
- check for correct programming of the J14 engine identification connector (Ref. AMM TASK 73-21-90-000-002) and (Ref. AMM TASK 73-21-90-400-002).
1 If the fault continues:
_
- replace the J14 engine identification connector (Ref. AMM TASK 73-21-90-000-002) and (Ref. AMM TASK 73-21-90-400-002).
a If the fault continues:
_
- replace the ECU1 (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
B. Do the test given in Para. 3.
F 『R EEFF : ALL E ∞∞73-20-00∞∞∞∞∞∞∞∞∞∞Page A228
E E Aug 01/05 E E ECES
E TASK 73-20-00-810-914
F 『
E C F M E
E E
E 56 E
E E
中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發動機燃油和控制 1(115)
