- find the average (r1+r2/2) (2.4 to 4.2 ohms).

 1 If the resistance values are out of the specified limits:
_
 - replace the TCC sensor (Ref. AMM TASK 73-21-70-000-002) and (Ref. AMM TASK 73-21-70-400-002).
 NOTE : Tighten the connector by hand plus one eighth of a
____ turn. If necessary use soft nose pliers.
 2 If the resistance values are in the specified limits:
_ NOTE : Tighten the connector by hand plus one eighth of a
____ turn. If necessary use soft nose pliers.
 - disconnect the harness CJ13 from the 6 o'clock junction box and do a check of the CJ13 resistance cable between: . pins 14 and 15 (2.4 to 4.2 Ohms) . pins 14 and 4 (> 10 Megohms) . pin 14 and ground (> 10 Megohms).
 a If the resistance values are out of the specified limits:
_
 - replace the harness CJ13 (Ref. AMM TASK 73-21-50-000-029) and (Ref. AMM TASK 73-21-50-400-029).
 F 『 EEFF : ALL E ∞∞73-20-00∞∞∞∞∞∞∞∞∞∞Page A270
 E E Aug 01/05 ERE
ECES

 F 『
 E C F M E
 E E
 E 56 E
 E E
 b If the resistance values are in the specified limits:

_
 - disconnect the harness HJ13 from the ECU receptacle and do a check of the resistance between: . pins 18 and 19 (2.4 to 4.2 Ohms) . pins 18 and 17 (> 10 Megohms) . pin 18 and ground (> 10 Megohms).
 * If the resistance values are out of the specified limits:
 - replace the harness HJ13 (Ref. AMM TASK 73-21-50-000-046) and (Ref. AMM TASK 73-21-50-400-046).
 * If the resistance values are in the specified limits:
 - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
 B. For configuration post SB CFMI73-046.
 NOTE : The failure message is triggered if the TCC sensor channel B input
____ is invalid (signal out of range) and the fault lasts for more than 20 seconds.
 (1) If the failure message TCC SNSR, J13, ECU is not confirmed:

 (a) Do the following trouble shooting at next maintenance opportunity:
 - disconnect the CJ13 connector (TCC-B) from the TCC sensor (3 O'Clock).

 - visually examine the harness connector and sensor receptacle for damaged pins or contamination/oxidation.

 - if damage is found, repair or replace as required.

 - do a cleaning of the connector and receptacle using a bristle brush with stoddard solvent (Material No. CP2011) (Ref. AMM TASK 73-21-50-210-002).

 - connect the harness connector (TCC-B) to the sensor. Tighten the connector by hand plus one eighth of a turn. If necessary use soft nose pliers.

 (2) If the failure message TCC SNSR, J13, ECU is not confirmed but is repetitive:

 (a) Do the following trouble shooting at next maintenance opportunity:
 - disconnect the HJ13 connector from the ECU connector.

 - visually examine the harness connector and ECU receptacle for damaged pins or contamination/oxidation.

 - if damage is found, repair or replace as required.

 - do a cleaning of the harness connectors and receptacles using a bristle brush with stoddard solvent (Material No. CP2011) (Ref. AMM TASK 73-21-50-210-002).

 F 『 EEFF : ALL E ∞∞73-20-00∞∞∞∞∞∞∞∞∞∞Page A271
 E E Aug 01/05 ERE ECES

 F 『 E C F M E E E E 56 E E E 1 If the fault continues:

_
 - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
 2 If the fault continues:
_
 - replace the harness HJ13 (Ref. AMM TASK 73-21-50-000-046) and (Ref. AMM TASK 73-21-50-400-046).
 3 If the fault continues:
_
 - disconnect the CJ13 connector (TCC-B) from the TCC sensor (3 O'Clock).

 - do a cleaning of the harness connector using a bristle brush with stoddard solvent (Material No. CP2011) (Ref. AMM TASK 73-21-50-210-002).

 - replace the TCC sensor (Ref. AMM TASK 73-21-70-000-002) and (Ref. AMM TASK 73-21-70-400-002).

 NOTE : Tighten the connector by hand plus one eighth of a
____ turn. If necessary use soft nose pliers.
 4 If the fault continues:
_
 - replace the harness CJ13 (Ref. AMM TASK 73-21-50-000-029) and (Ref. AMM TASK 73-21-50-400-029).
 (3) If the failure message TCC SNSR, J13, ECU is confirmed only on channel B:
 (a) Disconnect the connector (TCC-B) on the harness CJ13 from the TCC sensor (3 O'Clock) and do a check of the resistance as follows:
 - place the positive (+) lead of an ohmmeter on the TCC sensor pin A and the negative (-) lead of the ohmmeter on the TCC sensor pin B. Record as r1.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發動機燃油和控制 1(132)