(b)
Tighten the four fasteners to attach the ACARS IDU to the panel.
S 864-006
(3) Remove the DO-NOT-CLOSE tags and close these circuit breakers:
(a) P18 Load Control Center
1) AC ACARS MU
2) DC ACARS MU
3) AC ACARS IDU
D. Interactive Display Unit Test
S 864-009
(1)
Supply electrical power (Ref 24-22-00/201).
S 714-007
(2)
Do a test of the ACARS IDU operation:
(a)
Touch the MISCELLANEOUS key on the ACARS MENU page.
(b)
Touch the DISPLAY/ILLUM TEST key on the MISCELLANEOUS MENU page.
(c)
Make sure the LAMP INTESITY page comes into view on the IDU:
................................. LAMP INTENSITY
LO HI 1 2 3 4 5 6 7 8
> SELCAL TEST > LAMP TEST
MENU **** .................................
(d)
Set the LAMP INTENSITY to the necessary intensity.
(e)
Touch the LAMP TEST key.
1) While the LEDs come on and go off in the test sequence, look for these conditions: a) No 2 adjacent LEDs are burned out. b) No 3 LEDs in a square inch are burned out. c) No more than 5 LEDs on the screen are burned out.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
23-27-12
ALL ú ú 06A Page 402 ú Nov 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 864-010
(3) Remove electrical power (Ref 24-22-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
23-27-12
ALL ú ú 01A Page 403 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
ACARS PRINTER - REMOVAL/INSTALLATION
____________________________________
1. General_______
A. There are two tasks in this procedure. The first task is the removal of the ACARS printer. The second task is the installation of the ACARS printer. The installation task includes a test of the printer operation.
B. The ACARS printer is installed in the P8 Aft Electronics Control Panel in the control cabin.
TASK 23-27-22-004-013
2. ACARS Printer Removal_____________________
A. Access
(1) Location Zones
101/102 Control Cabin
B. Procedure
S 864-002
(1) Open these circuit breakers and attach DO-NOT-CLOSE tags:
(a) P18 Load Control Center
1) AC ACARS PRINTER
S 024-003
(2) Remove the ACARS printer:
(a)
Loosen the four fasteners on the front panel of the ACARS printer.
(b)
Slowly remove the ACARS printer until you can get access to the electrical connector.
(c)
Disconnect the electrical connector at the rear of the ACARS printer.
(d)
Install dust caps on the ends of the electrical connectors.
TASK 23-27-22-404-004
3. ACARS Printer Installation__________________________
A. References
(1) 24-22-00/201, Manual Control
B. Access
(1) Location Zones
101/102 Control Cabin
C. Procedure
S 864-011
(1) Make sure these circuit breakers are open:
(a) P18 Load Control Center
1) AC ACARS PRINTER
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
23-27-22
ALL ú ú 02A Page 401 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(2) S 424-005Install the ACARS printer: (a) Remove the dust caps from the electrical connectors. (b) Connect the electrical connector to the ACARS printer. (c) Install the ACARS printer. (d) Tighten the four fasteners on the front of the ACARS printer.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 通訊 COMMUNICATIONS(43)
