C. Procedure
 S 864-006
 (1)  Make sure these circuit breakers are open with DO-NOT-CLOSE tags attached:
 (a)  
P6-1 Load Control Center - Right
 1) CAPT COMPASS XFMR (ALTN)
 2) INSTR XFMR - 2

 (b)  
P18 Load Control Center - Left
 1) F/O CCOMPASS XFMR (ALTN)
 2) INSTRUMENT XFMR - 1

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITHOUT EFIS ú

 34-28-71

 ú ú 02 Page 402 ú Nov 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (2)  S 424-007Do these steps to install an HSI. (a) Connect the electrical connector to the HSI.
 CAUTION:_______ CAREFULLY INSTALL THE HSI INTO THE INSTRUMENT PANEL. TOO MUCH FORCE CAN CAUSE DAMAGE TO THE ELECTRICAL CABLE AT THE REAR OF THE HSI.
 (b) (c)  Carefully install the HSI into the clamp at the rear of the instrument panel.Tighten the higher right screw and the lower left screw on the front of the HSI.
 (3)  S 864-008Remove the DO-NOT-CLOSE tags and close these circuit breakers: (a) P6-1 Load Control Center - Right 1) CAPT COMPASS XFMR (ALTN) 2) INSTR XFMR - 2
 (b)  P18 Load Control Center - Left 1) F/O CCOMPASS XFMR (ALTN) 2) INSTRUMENT XFMR - 1
 (4)  S 864-009Supply the electrical power (Ref 24-22-00/201).
 (5)  S 764-010Make sure the panel lights on the HSI come on.
 (6)  S 864-011Remove the electrical power if it is not necessary (Ref 24-22-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITHOUT EFIS ú

 34-28-71
 ú ú 02 Page 403 ú Mar 15/91

BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 RADIO DIGITAL DISTANCE MAGNETIC INDICATOR - REMOVAL/INSTALLATION
________________________________________________________________
 1.  General_______
 A.  There are two tasks in this subject. The first task is for the removal of a radio digital distance magnetic indicator (RDDMI). The second task is for the installation of a RDDMI.
 B.  Two RDDMIs are installed in the airplane. One RDDMI is installed on the captain's main instrument panel. The other RDDMI is installed on the first officer's main instrument panel.
 C.  Each RDDMI is installed through a hole in the flight instrument panel into a clamp. The clamp holds the RDDMI in its position. Two screws on the front of the RDDMI adjust the clamp.
 D.  Each RDDMI has one electrical connector attached to the rear of the unit.
 TASK 34-28-81-004-001
 2.  RDDMI Removal_____________
 A.  Access
 (1)  Location Zones
 101 Control Cabin - Left
 102 Control Cabin - Right

 B.  Procedure
 S 864-003
 (1)  AIRPLANES WITHOUT EFIS;
 set the COMPASS switch to the NORMAL position.

 NOTE: The COMPASS switch is installed on the overhead panel P5.
____
 S 864-005
 (2)  AIRPLANES WITH EFIS;
 set the IRS switch to the NORMAL position.

 NOTE: You can find the IRS switch on the P5 Overhead Panel.
____
 S 864-006
 (3)  Make sure these circuit breakers are open with DO-NOT-CLOSE tags attached:
 (a)  P6 Circuit Breaker Panel
 1) INSTRUMENT XFMR-2 (CAPT's RDDMI)

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-28-81

 ALL  ú ú 02 Page 401 ú Nov 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (b)  P18 Circuit Breaker Panel
 1) INSTRUMENT XFMR-1 (F/O's RDDMI)

 S 024-007
 (4)  Do these steps to remove an RDDMI.
 (a) Loosen the higher right screw and the lower left screw.
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 導航 NAVIGATION 2(97)