曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 C.  The inertial reference system (IRS) supplies the data shown on the VSIs.
 D.  Each VSI is installed through a hole in the instrument panel into a clamp. The clamp holds the VSI in its position. Two screws on the front of the VSI adjust the clamp.
 E.  Each VSI has one electrical connector attached to the rear of the unit.
 TASK 34-28-91-004-001
 2.  VSI Removal___________
 A.  Access
 (1)  Location Zones
 101 Control Cabin - Left
 102 Control Cabin - Right

 B.  Procedure
 S 864-002
 (1)  Open these circuit breakers and attach DO-NOT-CLOSE tags:
 (a)  
P6 Circuit Breaker Panel
 1) F/O VSI

 (b)  
P18 Circuit Breaker Panel
 1) CAPT VSI

 (c)  
P41 Circuit Breaker Panel
 1) 5V AC SEC

 (d)  
P42 Circuit Breaker Panel
 1) 5V AC SEC

 

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH INERTIAL VERTICAL SPEED ú

 34-28-91

 INDICATOR  ú
 ú 01 ú BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.  Page 401Nov 15/96 

A
737-300/400/500MAINTENANCE MANUAL
 S 024-003
 (2)  Remove the VSI:
 (a) Loosen the top right screw and the bottom left screw.
 NOTE: Do not loosen the top left screw or the bottom right
____ screw. These screws hold the VSI clamp behind the instrument panel.
 (b)  
Push on the top right screw and the bottom left screw to loosen the clamp.

 CAUTION:_______CAREFULLY REMOVE THE VSI FROM THE INSTRUMENT PANEL. TOO MUCH FORCE CAN CAUSE DAMAGE TO THE ELECTRICAL CABLE AT THE REAR OF THE VSI.

 (c)  
Pull the indicator from the instrument panel.

 CAUTION:_______DO NOT TOUCH THE CONNECTOR PINS ON THE VSI. IF YOU TOUCH THESE PINS, ELECTROSTATIC DISCHARGE FROM YOUR BODY CAN CAUSE DAMAGE TO THE VSI.

 (d)  
Disconnect the electrical connector from the indicator.

 (e)  
Install a dust cap on the electrical connector.

 TASK 34-28-91-404-004
 3.  VSI Installation________________
 A. References
 (1)  AMM 24-22-00/201, Manual Control
 B. Access
 (1)  Location Zones
 101 Control Cabin - Left
 102 Control Cabin - Right

 C. Procedure
 S 864-005
 (1)  Make sure these circuit breakers are open with DO-NOT-CLOSE tags attached:
 (a)  P6 Circuit Breaker Panel
 1) F/O VSI

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH INERTIAL VERTICAL SPEED ú

 34-28-91

 INDICATOR  ú
 ú 01 ú BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.  Page 402Nov 15/96 

A 737-300/400/500MAINTENANCE MANUAL
 (b) (c) (d)  P18 Circuit Breaker Panel 1) CAPT VSIP41 Circuit Breaker Panel 1) 5V AC SECP42 Circuit Breaker Panel 1) 5V AC SEC
 (2)  S 424-006Install the VSI: (a) Remove the dust cap from the electrical connector. (b) Connect the electrical connector to the VSI.
 CAUTION:_______ CAREFULLY INSTALL THE VSI INTO THE INSTRUMENT PANEL. TOO MUCH FORCE CAN CAUSE DAMAGE TO THE ELECTRICAL CABLE AT THE REAR OF THE VSI.
 (c) (d)  Put the indicator into the instrument panel.Tighten the top right screw and the bottom left screw on the front of the VSI.
 (3)  S 864-007Remove the DO-NOT-CLOSE tags and close these circuit breakers: (a) P6 Circuit Breaker Panel 1) F/O VSI (b) P18 Circuit Breaker Panel 1) CAPT VSI (c) P41 Circuit Breaker Panel 1) 5V AC SEC (d) P42 Circuit Breaker Panel 1) 5V AC SEC
 (4)  S 864-008Supply electrical power (AMM 24-22-00/201).
 (5)  S 764-009Make sure the panel lights on the VSI come on.
 (6)  S 864-010Remove electrical power if it is not necessary (AMM 24-22-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH INERTIAL VERTICAL SPEED ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 導航 NAVIGATION 2(99)