NOTE: One of the following pumps is necessary to actuate the power units: . DTL02MAPP1000 pneumatic pump 10,000 psi . DLT01MAPM1000 manual pump 10,000 psi
DEUTSCH LIGHTWEIGHT TOOLS TABLE B
NOTE: The -12 size swage die is different in outer diameter than the swage dies used before.
Swage and Inspection Tool Part Numbers
Figure 825
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-11-05
ALL ú ú 01 Page 880F ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
L10164
A
747-400
MAINTENANCE MANUAL
DAMAGE
NOTE: ALL DIMENSIONS ARE IN INCHES.
Minimum Straight Length for Permaswage Fitting Installation
Figure 826
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-11-05
ALL ú ú 01 Page 880G ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
L10215
A
747-400
MAINTENANCE MANUAL
TUBE
Tube Splice Repair
Figure 827
L10236
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-11-05
ALL ú ú 01 Page 880H ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
MATERIAL SURFACE Bare or alodine PROCEDURE TO CLEAN TUBE Solvent clean
Anodize . Hand apply abrasive material, 180-grit or finer: . . Abrasive Scotch Brite, Type A Fed Spec P-C-451 Fed Spec P-P-121
Primer/paint (flammable) MEK (refer to TT-T-261) (flammable) for primed surfaces (MIL-P-6889) and Lacquer thinner (refer to TT-T-266) 1. Hand apply abrasive material, 240-grit or finer 2. lacquer base paint/enamel
Cleaning and Paint Removal Procedures for Aluminum Tubes
FIgure 828
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-11-05
ALL ú ú 01 Page 880I ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
L10387
A
747-400
MAINTENANCE MANUAL
0.150 INCH MIN
A
MARK FOR THE MINIMUM TUBE INSERTION DEPTHS
Witness Mark Location and Usual Marking Procedures
Figure 829
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-11-05
ALL ú ú 01 Page 880J ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
L10391
A
747-400
MAINTENANCE MANUAL
GAGE D12-9892-SIZE
INSERTION WITNESS MARK BE
CLEAR OF THE FITTING END
1/4 (04) (INCHES) TUBE DIAMETER 0.315 (INCHES) SWAGED DIAMETER MAX A DIMENSIONS 0.46 (INCHES) SWAGED LENGTH MIN B DIMENSIONS
3/8 (06) 0.447 0.53
1/2 (08) 0.606 1.02
5/8 (10) 0.735 1.02
3/4 (12) 0.863 1.02
1 (16) 1.181 1.406
1-1/4 (20) 1.390 1.406
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 STANDARD PRACTICES - AIRFRAME(49)
