EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-15-11
ALL ú ú 01 Page 207 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
P11 PANEL
USUAL LOCATION FOR DATA LOADER CONTROL PANEL
SEE B
ALTERNATIVE LOCATION FOR DATA LOADER CONTROL PANEL
SEE B
AIRBORNE DATA
LOADER
SEE A
FLIGHT COMPARTMENT
ADL
FAIL
DISPLAY
EJECT
BUTTON
PROG CHNG COMP RDY XFER R/W HRDW DISK DISK
DRIVE DRIVE
DISPLAY
EJECT
BUTTON DISK DRIVE
LIGHT
DISK FRONT
DRIVE PROG CHNG DISK CHANGE IS REQUIRED DATA TRANSFER IN PROGRESS COVER
COMP DATA TRANSFER IS COMPLETE
LIGHT XFER RDY DATA TRANSFER FAILURE UNIT READY FOR OPERATION FRONT
HRDW R/W SYSTEM TEST FAILURE UNABLE TO ACCESS DISK DATA COVER
AIRBORNE DATA LOADER AIRBORNE DATA LOADER
[ALLIED SIGNAL (SUNDSTRAND)] (TELEDYNE)
A A
On-Airplane Software Installation
Figure 201 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-15-11
ALL ú ú 01 Page 208 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
L08736
A
747-400 MAINTENANCE MANUAL
NORMALNORMAL
SYSTEM SYSTEM
(EXAMPLE) (EXAMPLE)
SELECT
SELECT SWITCH
SWITCH
B
B
On-Airplane Software Installation Figure 201 (Sheet 2)
L08764
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-15-11
ALL ú
ú 01 Page 209
ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(b) PDLs are not Boeing supplied parts. Refer to the data loader supplier for instructions for PDL operation.
B. References
(1)
AMM 24-22-00/201, Control
C.
Access
(1)
Location Zones
222 Control Cabin, RH
D.
Allied Signal (Sundstrand) Airborne Data Loader Procedure
S 862-003
(1) The Allied Signal ADL has these status lights:
(a)
PROG (In Progress) - shows as software installation occurs.
(b)
CHNG (Change) - shows when it is time to install the next disk.
(c)
COMP (Complete) - shows when the software installation is completed.
(d)
RDY (Ready) - shows when the disk is in the disk drive and the ADL is ready to install the software in the component. 1) If the RDY indication flashes, then the data loader is in
standby mode while it waits for the component to validate the data.
(e)
XFER (Transfer Fail) - shows when the software installation is not completed. Open and close the circuit breaker for the component, and start the installation again.
(f)
R/W (Read/Write) - shows when the ADL cannot read or write the data on the disk. Open and close the circuit breaker for the component, and start the installation again. If the problem continues, then replace the disk.
(g)
HRDW (Hardware) - shows when the ADL fails the self test.
S 862-004
(2) Supply electrical power (AMM 24-22-00/201).
(a) Make sure that the power is not removed while you install software.
NOTE: A power interruption will cause a failure of the
____
software installation.
S 862-005
(3) Make sure that the system select switch on the data loader control panel (P11) is set to NORMAL.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 STANDARD PRACTICES - AIRFRAME(93)
