(2)
Drive Tool - 5254-1 (for Alemite 1646B and
1992B lubrication angle fittings)
D. Consumable Materials
(1)
B00722 Solvent - P-D-680
(2)
B00083 Solvent Aliphatic Naphta - TT-N-95
(3)
G00262 Nitrogen - Liquid, MIL-P-27401
(4)
C00316 Primer - Loctite Grade T (747I)
(5)
Adhesive:
(a)
G00106 Retaining Loctite 675 or MIL-R-46082
(b)
G00106 Loctite RC/680 or MIL-R-46082
(6)
Cotton Swab (Commercially Available)
E. Install a New Lubrication Fitting
S 844-012
(1)
Get an applicable standard fitting to install in the hole.
S 164-003
(2)
Do these steps to clean the lubrication fitting hole:
(a) Use a cotton swab to remove as much grease as possible from the inner surface of the lubrication fitting hole.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-11-27
ALL ú ú 02 Page 401 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
DESIGN LUBE HOLE DIA IS 0.188/0.189 INCHES
LUBE HOLE LUBE FITTING
DIA (X) DIA
(INCHES) (INCHES)
0.194 MAX 3/16 1
0.195-0.247 1/4 MODIFIED 1
0.248-0.249 1/4 2
0.250-0.254 1/4 1
INSTALL WITH ADHESIVE INSTALLATION WITH ADHESIVE OPTIONAL
ALL DIMENSIONS ARE IN INCHES
X (NOT SHOWN) = HOLE DIA IN MATING COMPONENT
A = SHANK DIA (X MINUS 0.007/0.012)
B = SERRATION OD (X PLUS 0.005/0.010)
C = SERRATION ROOT OD (X MINUS 0.003/0.010)
Lubrication Fitting Modification and Installation
Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-11-27
ALL ú ú 01 Page 402 ú Oct 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(b)
Clean the hole to a depth of at least 0.5 inch with solvent or detergent on a clean cotton swab.
(c)
Clean the hole until you can see no more grease or dirt removed from the hole.
S 424-011
CAUTION: MAKE SURE YOU USE THE CORRECT TOOL TO INSTALL THE LUBRICATION
_______ FITTING. MOVE THE FITTING IN A STRAIGHT LINE TO PREVENT DAMAGE TO THE MATING PART.
(3) Use the correct drive tool to install the fitting into the hole in the part the fitting connects to.
F. Install a Lubrication Fitting to Replace a Fitting that was Blown Out
S 844-013
(1) Get a special approved or an oversized fitting to install in the hole.
S 164-006
(2) Do these steps to clean the lubrication fitting hole: (a) Use a cotton swab to remove as much grease as possible from the inner surface of the lubrication fitting hole. (b) Clean the hole to a depth of at least 0.5 inch with solvent or detergent on a clean cotton swab. (c) Clean the hole until you can see no more grease or dirt removed from the hole.
S 394-009
(3) Do these steps to apply the primer: (a) Use a cotton swab to apply a thin layer of primer to the inner diameter of the hole.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 STANDARD PRACTICES - AIRFRAME(79)
