S 034-014-C00
(3)
Remove the lockwire and disconnect the line coupling nut of the CDP from the CBP sensor.
S 034-015-C00
(4)
Remove the lockwire and disconnect the line coupling nut of the CBP from the CBP sensor.
S 024-016-C00
CAUTION:_______DO NOT TURN THE SENSOR BELLOWS ASSEMBLY OF THE CBP. ENGINE OPERATION COULD BE CHANGED AND THE MEC WILL HAVE TO BE CALIBRATED AGAIN.
(5) Remove the CBP sensor (Fig. 401).
(a) Remove the four screws and washers that attach the CBP sensor to the MEC.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-21-10
ALL ú ú C01 Page 401 ú Jul 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
SEE A
MAIN ENGINE CONTROL (MEC) SEE B
BOX MEC CONTROL CBP SENSOR CDP LINE CBP LINE
MEC
O-RING A
SEE C WASHER SCREW
O-RING FILTER SENSOR CBP
O-RING CBP ASSEMBLY BELLOWS B WASHER SCREW
O-RING MATING SURFACE FILTER O-RING
C CBP Sensor/Filter Installation Figure 401 GMM-1077366-02-B
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-21-10
ALL ú ú C01 Page 402 ú Jul 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(b)
Remove and discard the o-ring from the CBP sensor base.
(c)
Remove and discard the o-ring from the MEC groove.
(d)
Remove the CBP sensor filter. 1) Discard the o-rings of the CBP sensor filter. 2) Keep the CBP sensor filter.
TASK 73-21-10-404-017-C00
3. CBP Sensor Installation_______________________
A. Consumable Materials
(1) Petrolatum - Pure Mineral (CP 2102)
B. References
(1)
AMM 71-00-00/501, Power Plant
(2)
AMM 78-31-00/201, Thrust Reverser System
C. Access
(1)
Location Zones
506 Engine No. 1 - Aft side of MEC
606 Engine No. 2 - Aft side of MEC
(2)
Access Panels 5783L Engine No. 1 - Fan Duct Cowl and Thrust Reverser Half 5838R Engine No. 2 - Fan Duct Cowl and Thrust Reverser Half
D. Procedure
S 424-018-C00
(1) Install the packing on the CDP sensor.
(a)
Lightly apply a layer of petrolatum on two new o-rings.
(b)
Install the o-rings on the filter.
(c)
Install the filter in the CBP sensor.
(d)
Lightly apply a layer of petrolatum on two new o-rings.
(e)
Install the o-rings in the base of the CBP sensor and the groove of the MEC.
S 434-013-C00
(2) Attach the CDP sensor and CBP sensor coupling nuts to the CBP sensor ports (nipples) as follows:
(a)
Do a check of the nipples and nuts to see that they are clean and have no damage.
(b)
If the nipples and nuts are dirty or damaged, replace them.
WARNING:_______DO NOT LET ENGINE OIL STAY ON YOUR SKIN. USE ENGINE OIL IN AREA WITH GOOD VENTILATION. ENGINE OIL IS POISONOUS AND CAN BE ABSORBED THROUGH YOUR SKIN. ENGINE OIL FUMES CAN IRRITATE YOUR RESPIRATORY TRACT.
(c)
If the nipples and nuts do not show damage, apply a layer of engine oil to them.
(d)
Connect the CBP line to the CBP sensor nipple.
(e)
Tighten the nut to 135-150 pound-inches
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 發動機燃油和控制(140)
