(i)  
Move the MEC forward from the left side, then move it rearwards, and then move it forward.

 (j)  
Turn the drive shaft for the fuel pump to align the splines on the fuel pump with the splines on the MEC.

 (k)  
Attach the MEC to the fuel pump with the six washers and the six self-locking nuts.

 (l)  
Use the sequence below to tighten the nuts to 55-65 pound-inches (6-7 Newton meters). ~............................................................ | MEC NUT TIGHTENING | APPROXIMATE LOCATION | | SEQUENCE | LOOKING FORWARD | .............................................................. | First | 12 O'clock | .............................................................. | Second | 3 O'clock | .............................................................. | Third | 7 O'clock | .............................................................. | Fourth | 2 O'clock | .............................................................. | Fifth | 6 O'clock | .............................................................. | Sixth | 10 O'clock | 2.............................…..............................1

 (m)  
Tighten the nuts, with the sequence above, again.

 (n)  
Tighten the nuts to a torque of 100-130 pound-inches (11-15 Newton meters).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 73-11-01
 ALL  ú ú C02 Page 436 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 434-044-C00
 CAUTION: DO NOT REMOVE THE PROTECTIVE CAPS FROM THE MEC PORTS UNTIL YOU
_______ INSTALL THE FITTINGS. IF YOU REMOVE ALL THE CAPS, CONTAMINATION OF THE PORTS CAN OCCUR.
 (6)  
Install new O-rings, lubricated with petrolatum, on the fittings.

 S 434-046-C00

 (7)  
Install the fittings that follow in the applicable MEC ports (Fig. 411, 412 and 413):

 NOTE: This step is not necessary if the MEC to be installed has
____
 all the fittings installed.

 NOTE: The VSV/VBV ROD end fitting is permanently installed on
____
 the MEC and is not removed.

 (a)  
VBV OPEN - Tighten to 270-300 pound-inches
 (30-34 Newton meters).

 (b)  
VSV HEAD - Tighten to 270-300 pound-inches
 (30-34 Newton meters).

 (c)  
TC1 - Tighten to 180-200 pound-inches (20-25 Newton meters). 1) Install the flexible hose to the TC1 fitting. 2) Tighten the coupling nut to 270-300 pound-inches

 (30-34 Newton meters).

 (d)  
TC2 - Tighten to 135-150 pound-inches (15-17 Newton meters). 1) Install the flexible hose to the TC2 fitting. 2) Tighten the coupling nut to 135-150 pound-inches

 (15-17 Newton meters).

 (e)  
ENGINES WITHOUT THE HPTCC TIMER; Do these steps if the TC3 and/or the PC ports do not have plugs installed: 1) Install new O-rings, lubricated with petrolatum, on each

 hex-head plug. 2) Install the plugs in the TC3 and/or PC ports. 3) Tighten the plugs to 40-60 pound-inches
 (4.5-6.8 Newton meters).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 73-11-01
 ALL  ú ú C02 Page 437 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(f)  ENGINES WITH THE HPTCC TIMER;
 Do these steps to attach the TC3 and the PC lines:
 1) TC3 - Tighten to 135-150 pound-inches

 (15-17 Newton meters).
 a) Connect the flexible hose to the TC3 fitting.
 b) Tighten the coupling nut to 135-150 pound-inches

 (15-17 Newton meters). 2) PC - Tighten to 135-150 pound-inches (15-17 Newton meters).
 (g)  
PCR - Tighten to 135-150 pound-inches
 (15-17 Newton meters).

 (h)  
HEATED SERVO SUPPLY (FUEL-OUT) - Tighten to
 360-400 pound-inches (41-45 Newton meters).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 發動機燃油和控制(20)