NOTE: Do not disconnect the nose cap from the conduit cap.
____
(c)
Carefully install the threaded part of the conduit cap into the MEC slotted bracket.
CAUTION:_______DO NOT TWIST THE FEEDBACK CABLE. USE TWO WRENCHES WHEN YOU TIGHTEN THE NOSE CAP; ONE WRENCH ON THE NOSE CAP AND ONE ON THE CONDUIT CAP.
(d)
Install the nose cap on the conduit cap.
1) Tighten the nose cap to 180-200 pound-inches
(20.3-22.6 Newton meters).
2) Install the lockwire.
NOTE: Do not connect the VBV feedback cable to the MEC
____ feedback arm at this time. The cable will be connected when you do the VBV Feedback Cable Travel Check procedure (AMM 71-00-00/501, Test No. 6).
S 434-085-C00
(19) Put the support tube into position.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-11-01
ALL ú ú C03 Page 449 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 434-086-C00
(20)
Install the two bolts, washers and nuts and the clampshell and clamp that attach the support tube to the MEC and the transfer gearbox (Fig. 402, Sheet 1).
S 434-087-C00
(21)
Put the electrical cable into position.
S 434-088-C00
(22)
Install the six screws, washers, clamps and nuts that attach the electrical cable to the MEC and the transfer gearbox (Fig. 402, Sheet 1):
(a) Tighten the clamps and the clampshell.
S 424-098-C00
(23)
Tighten the fuel inlet line at the strut disconnect panel.
S 414-059-C00
(24)
Install the fuel control box and the throttle push-pull cables on the MEC (AMM 76-11-08/401).
S 414-071-C00
(25)
Remove the protective caps on the MEC.
S 434-084-C00
(26)
Connect these electrical connectors (Fig. 402):
(a)
VBV reset solenoid connector, D3012, installed on the top side of the MEC.
(b)
The idle reset solenoid connector, D3016, installed on the lower inboard side of the MEC.
(c)
The power lever angle (PLA) position connector (blue cable), installed on the lower aft side of the MEC.
S 414-060-C00
(27)
Install the connector bracket (to the aft half of the connector, D2876) to the connector bracket plate on the MEC with the two (non-epoxied) allen screws.
S 414-061-C00
(28)
Connect the TLA electrical connector, D2876, to the connector bracket.
(29)
Fill the engine oil system (AMM 12-13-11/301).
S 614-097-C00
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-11-01
ALL ú ú C03 Page 450 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 414-075-C00
WARNING:_______ OBEY THE INSTRUCTIONS IN THE PROCEDURE TO CLOSE THE THRUST
REVERSERS. IF YOU DO NOT OBEY THE INSTRUCTIONS WHEN YOU CLOSE
THE THRUST REVERSER, INJURIES TO PERSONS AND DAMAGE TO
EQUIPMENT CAN OCCUR.
(30)
Close the thrust reverser (AMM 78-31-00/201). S 414-073-C00
(31)
Close the left fan cowl panels (AMM 71-11-02/201) S 204-063-C00
(32)
Do Test No. 6 - MEC Trim (AMM 71-00-00/501). S 864-064-C00
(33)
Remove the DO-NOT-OPERATE tags from the engine start lever.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-11-01
ALL ú ú C01 Page 451 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 發動機燃油和控制(26)
