(5)  
Pressurize hydraulic system No. 4 (AMM 29-11-00/201).

 (6)  
Release the parking brake.

 S 862-010
 S 862-011
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-41-00
 ALL  ú ú 01 Page 206 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 G. Capacity Test of Brake System Fuses
 S 722-012
 (1)  
Do these steps to do a test of the normal brake system fuses (Fig. 202):

 (a)  
Remove the screw and washer from the end of the bleeder valve.

 (b)  
Install a bleed hose on the end of the bleeder valve.

 (c)  
Put a container with a minimum capacity of 1 U.S. gallon near the brake bleed port so that fluid can flow from the bleed hose into the container.

 (d)  
Push on the brake pedals to their maximum travel and apply full brake pressure.

 NOTE: You can set the parking brake to keep brake pressure
____ applied during the fuse capacity test.
 (e)  
Put goggles on for eye protection.

 (f)  
While you apply full brake pressure, open the bleeder valve one and one-half turns.

 (g)  
Let the fluid flow into the container until the flow stops to show that the fuse has closed.

 NOTE: Fluid can flow out of the brake very quickly and
____ intermittently. Make sure it does not splash out of the container.
 CAUTION: TIGHTEN THE BRAKE BLEEDER VALVE TO 45 POUND-INCHES MAXIMUM
_______ TO INSTALL OR CLOSE THE VALVE. IF YOU TIGHTEN THE VALVE TO MORE THAN 45 POUND-INCHES, YOU WILL DAMAGE THE BRAKE BLEEDER ADAPTER AND CAUSE THE BRAKE TO HAVE A LEAK.
 (h)  
Close the bleeder valve.

 (i)  
Make sure that the quantity of fluid collected in the container is 60-95 cubic inches (1.04-1.64 quarts).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-41-00
 ALL  ú ú 01 Page 207 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

METERED PRESSURE LINE
SUPPORT 
BRACKET 
SYSTEM 
PRESSURE 
LINE 
FILTER ANTISKID MODULE ASSEMBLY -
WING GEAR 
SHUTOFF 
VALVE  SEE  A  ANTISKID MODULE 
ASSEMBLY -
WING GEAR 
ANTISKID MODULE ASSEMBLY - SEE  A 
BODY GEAR 
SEE  B 

FUSE (4 LOCATIONS) HANDLE ANTISKID VALVE
(4 LOCATIONS) (4 LOCATIONS) RETURN LINE ANTISKID MODULE ASSEMBLY - WING GEAR SYSTEM
A
PRESSURE
FILTER LINE
SHUTOFF METERED
VALVE PRESSURE LINE
SCREEN FILTER
ANTISKID VALVE (4 LOCATIONS)
SUPPORT BRACKET
FUSE (4 LOCATIONS)
HANDLE (4 LOCATIONS)
ANTISKID MODULE ASSEMBLY - BODY GEAR
A
Normal Antiskid Module Assembly Figure 202
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-41-00
 ALL  ú ú 01 Page 208 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
 (2)  S 902-013If the quantity collected in the container is not as specified above, replace the hydraulic fuse (AMM 32-42-02/201).
 (3)  S 722-014Do the normal brake system fuses test at each of the sixteen brake positions.
 NOTE:____ Make sure to monitor the hydraulic reservoir quantity carefully. The normal brake system test series will use approximately 4.2 to 6.6 U.S. gallons of hydraulic fluid.
 (4)  S 862-015Remove the pressure from hydraulic system No. 4 (AMM 29-11-00/201).
 (5)  S 862-016Pressurize hydraulic system No. 1 or 2 (AMM 29-11-00/201).
 (6)  S 722-017Do these steps to do a test of the alternate brake system fuses (Fig. 203): (a) If it is installed, remove the screw and washer from the end of the bleeder valve. (b) Install a bleed hose on the end of the bleeder valve. (c) Put a container with a minimum capacity of 1 U.S. gallon near the brake bleed port and make sure the fluid can flow from the bleed hose into the container. (d) Push on the brake pedals to their maximum travel and apply full brake pressure. (e) Put goggles on for eye protection. (f) While you apply full brake pressure, open the bleeder valve one and one-half turns. (g) Let the fluid flow into the container until the flow stops to show that the fuse closed.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 6(30)