(b)  If it is necessary, install a new bearing in the lower bearing retainer.
 NOTE: To install a new bearing wet the surface of the bearing
____ with BMS 5-95 sealant and roller swage the bearing.
 (c)  
Install the lower bearing retainer with bolts, washers and nuts (3 locations).

 (d)  
Make sure the bearing for the top mounting bracket is a new bearing.

 (e)  
Apply the sealant to the bearing for the top mounting bracket.

 (f)  
Install the bearing in the top mounting bracket.

 (g)  
Install the top mounting bracket onto the higher end of the bus crank assembly.

 (h)  
Apply corrosion-preventive compound to the threads on the shaft of the bus crank assembly.

 (i)  
Install the nut and washer on the shaft.

 (j)  
Tighten the nut.

 (k)  
Turn the bus crank assembly.

 (l)  
Move the bus crank assembly aft through the cross-structure.

 (m)  
Install the lower end of the bus crank assembly into the lower bearing retainer.

 (n)  
Apply corrosion-preventive compound to the threads on the lower end of the shaft.

 (o)  
Install the washer and nut on the shaft.

 (p)  
Tighten the nut.

 (q)  
Attach the top mounting bracket to the structure with nuts, washers and bolts (4 locations).

 S 434-015
 (2)  
Do the steps that follow to connect the bus crank assembly to the rods:

 (a)  
Turn the lower lever arm on the bus crank assembly.

 1)  Make sure to have a clearance of 1.315-1.345 inches between the inboard edge of the lever and the outboard edge of the stop (Ref Fig. 401).

 (b)  
Hold the lever in this position.

 (c)  
Connect the two bus rods to the forward levers of the bus crank assembly. 1) Apply the sealant to the bolts, washers and nuts. 2) Install the bolts, washers and nuts.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-41-02
 ALL  ú ú 01 Page 407 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 3)  Tighten the nuts.
 (d)  Put the plastic strap into its position and install the two
 screws.
 (e)  Connect the horizontal pushrods to the bus crank assembly with
 nuts, bolts and washers.
 NOTE:____ Make sure that the rig pins in the bellcrank assembly
 can move in and out freely.  If the rig pins cannot move
 freely, adjust the rod ends.
 1)  Apply the sealant to the bolts, nuts and washers.
 2)  Install the bolts, washers and nuts.
 3)  Tighten the nuts.
 (f)  Connect the control quadrant push rod to the lower lever on the
 bus crank assembly with nuts, bolts and washers.
 1)  Apply the sealant to the bolt, nut and washer before
 installation.
 2)  Adjust the rod ends if it is necessary.
 (g)  Remove the rig pins from the bell crank assembly (4 locations).
 (h)  Remove the rig pins from the control quadrants of the metering
 valves.
 (i)  Release the lower lever on the bus crank assembly.

 S 414-017
 (3)  
Install the middle ceiling panels (AMM 25-22-01/401).

 S 864-018

 (4)  
Pressurize hydraulic systems No. 1, 2 and 4 (AMM 29-11-00/201).

 S 714-019

 (5)  
Do an operational test on the normal and reserve brake systems (AMM 32-41-00/501).

 S 714-024

 (6)  
Do a test of the left and right brake pedal switches, S1595 and S1596 (AMM 32-42-13/401).

 S 094-020
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO REMOVE
_______ THE DOOR LOCKS FROM THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT.
 (7)  
Do this task: "Removal of the Door Locks on the Wing Landing Gear" (AMM 32-00-30/201).

 S 094-028

 (8)  
Do this task: "Removal of the Door Locks on the Body Landing Gear" (AMM 32-00-30/201).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 6(55)