S 712-024

 (13)
 Do these steps to do a test of the normal brake system operation:

 (a)  
Push the brake pedals to the stops and hold them in this position. 1) Do a check for leaks of hydraulic fluid at each brake

 bleeder valve.
 2) Monitor the indicator on each brake assembly.
 3) Make sure that each brake operated to compress the heat
 stack.
 (b)  
Release the brake pedals. 1) Monitor the indicator on each brake assembly. 2) Make sure that each brake is released.

 (c)  
If a brake did not operate correctly, set the applicable hydraulic fuse again. 1) Get access to the applicable normal antiskid valve module. 2) Hold the fuse handle in the RESET position for 5 seconds

 minimum. 3) Do the normal brake operation test again.
 S 902-025
 (14) If you set a fuse again and the applicable brake does not operate correctly, replace the applicable hydraulic fuse (AMM 32-42-02/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-41-00
 ALL  ú ú 01 Page 212 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 862-026
 (15) Remove the pressure from hydraulic system No. 4 (AMM 29-11-00/201).
 S 862-051
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
_______ SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDERS, ELEVATORS, FLAPS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (16)
 Pressurize hydraulic system No. 1 or 2 (AMM 29-11-00/201).

 S 712-028

 (17)
 Do these steps to do a test of the alternate brake system operation:

 (a)  
Push the brake pedals to the stops and hold them in this position. 1) Do a check for leaks of hydraulic fluid at each brake

 bleeder valve. 2) Monitor the indicator on each brake assembly. 3) Make sure that each brake operated to compress the heat
 stack.
 (b)  
Release the brake pedals. 1) Monitor the indicator on each brake assembly. 2) Make sure that each brake is released.

 (c)  
If a brake did not operate correctly, set the applicable hydraulic fuse again. 1) Get access to the applicable alternate antiskid valve

 module assembly. 2) Hold the fuse handle in the RESET position for 5 seconds minimum. 3) Do the alternate brake operation test again.
 S 902-029
 (18)
 If you set a fuse again and the applicable brakes do not operate correctly, replace the applicable hydraulic fuse (AMM 32-42-02/201).

 H.
Put the Airplane Back to Its Usual Condition

 (1)  
Set the parking brake.

 S 092-052

 (2)  
Do this task: "Removal of the Door Locks from the Wing Landing Gear" (AMM 32-00-30/201).

 S 092-053

 (3)  
Do this task: "Removal of the Door Locks from the Body Landing Gear" (AMM 32-00-30/201).

 S 862-030
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-41-00
 ALL  ú ú 01 Page 213 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 862-032
 (4)  Remove the hydraulic power if it is not necessary (AMM/29-11-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-41-00
 ALL  ú ú 01 Page 214 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 HYDRAULIC BRAKE SYSTEM - ADJUSTMENT/TEST
________________________________________
 1.  General_______
 A.  This procedure has the instructions to do these tasks:
 (1)
Alternate Source Selector Valve - Operational Test
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 6(32)