34-12-01
 ALL  ú ú 05 Page 402 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 424-121
 WARNING:_______ DO NOT USE THE S242T210-207 ADCS WITH THE S242T210-205 ADCS.
 THE INSTALLATION OF THE S242T210-207 AND THE S242T210-205
 TOGETHER CAN CAUSE ALTITUDE AND AIRSPEED DIFFERENCES.  THESE
 DIFFERENCES SHOW ON THE CAPTAIN'S AND THE FIRST OFFICER'S
 PRIMARY FLIGHT DISPLAYS.
 CAUTION:_______ DO NOT TOUCH THE CONNECTOR PINS OR OTHER CONDUCTORS ON THE AIR
 DATA COMPUTER.  IF YOU TOUCH THESE CONDUCTORS, ELECTROSTATIC
 DISCHARGE FROM YOUR BODY CAN CAUSE DAMAGE TO THE AIR DATA

 COMPUTER.
 (3)  
Install the air data computer in the electronic equipment rack (AMM 20-11-22/401).

 S 424-223

 (4)  
AIRPLANES WITHOUT QUICK-DISCONNECTS ON THE -210 ADC AND PREVIOUS; Install quick-disconnects on the ADC.

 (a)  Do the system leak test (AMM 34-11-01/501).
 S 434-207
 CAUTION: DO NOT CONNECT THE PITOT-STATIC SYSTEM HOSES WHEN THE SYSTEM IS
_______ NOT AT AMBIENT PRESSURE. THIS CAN CAUSE DAMAGE TO THE AIR DATA COMPUTER.
 (5)  AIRPLANES WITH QUICK-DISCONNECTS ON THE ADC; AIRPLANES WITH -211 ADC AND SUBSEQUENT; Connect the pitot-static system hoses to the front panel of the air data computer.
 NOTE:____The Air Data Computers have quick-disconnect connectors. You do not have to do a leak test when you replace/reconnect a component. Visually make sure the quick-disconnects are fully connected and locked in a sealed position. If you are not sure the quick-disconnect is correct, do the system leak test (AMM 34-11-01/501).
 S 434-118
 (6)  
Make sure the pitot-static system hose connections are locked in the sealed position.

 (7)  
Supply electrical power (AMM 24-22-00/201).

 S 864-210
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-12-01
 ALL  ú ú 07 Page 403 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 864-185
 (8) Remove the DO-NOT-CLOSE tags and close these circuit breakers:
 (a)  P7 Overhead Circuit Breaker Panel
 1) 7A10, ADC L PWR
 2) 7A12, AOA L
 3) 7A13, AOA ALTN L
 4) 7A14, ADC R PWR
 5) 7A16, AOA R
 6) 7A17, AOA ALTN R
 7) 7J15, ADC C PWR

 S 864-119
 (9)  
Supply electrical power (AMM 24-22-00/201).

 S 714-004

 (10)
 Do a test of the air data computer with the steps that follow:

 CAUTION: DO NOT DO THE BITE TEST OF THE AIR DATA COMPUTER WHILE
_______ THERE IS PRESSURE IN THE PITOT-STATIC SYSTEM. THE ADC WILL GO INTO A FAILURE CONDITION AND TRANSMIT THIS CONDITION TO ITS INTERFACE SYSTEMS.
 (a)  Push and hold the test switch on the front panel of the ADC.
 NOTE: Use the left ADC when you replace the left ADC
____
 transformer.

 NOTE: Use the right ADC when you replace the right ADC
____
 transformer.

 NOTE: Use the center ADC when you replace the center ADC
____
 transformer.

 (b)  
Make sure that a (-) shows in the EXTERNAL SENSOR FAULT display on the front panel of the ADC.

 (c)  
Make sure that the FAIL indicator is black on the front panel of the ADC.

 (d)  
Release the test switch on the front panel of the ADC.

 E. Put the Airplane Back to Its Usual Condition
 S 864-212
 (1) Remove electrical power if it is not necessary (AMM 24-22-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-12-01
 ALL  ú ú 13 Page 404 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 TOTAL AIR TEMPERATURE PROBE - REMOVAL/INSTALLATION
__________________________________________________
 1.  General_______
 A.  This subject contains two tasks. The first task is to remove a total air temperature probe. The second task is to install a total air temperature probe. The second task includes a test of the temperature probe installation.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 導航 NAVIGATION 1(113)