Pitot-Static System - Component Location
Figure 102 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-11-00
 ALL  ú ú 01 Page 102 ú Feb 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 FAULT ISOLATION/MAINT MANUAL

Pitot-Static System - Component Location
Figure 102 (Sheet 2)

E17402
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-11-00
 ALL  ú ú 03 Page 103 ú Feb 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 FAULT ISOLATION/MAINT MANUAL
DRAIN PLUG VISCO JET DRAINDRAIN ASSEMBLY DE
SOURCE SELECT VALVE, V631
F

Pitot-Static System - Component Location
Figure 102 (Sheet 3)

E17408
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-11-00
 ALL  ú ú 03 Page 104 ú Oct 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 PITOT-STATIC SYSTEM - MAINTENANCE PRACTICE (PRESSURIZATION)
___________________________________________________________
 1.  General
_______
 A.  This subject gives one task. This task applies pressure to the
 pitot-static system to make an altitude and airspeed.

 TASK 34-11-00-862-001
 2.  Pressurization
______________
 A.  General
 (1)  These general instructions apply to the task.
 (a)  
When you apply a vacuum to a static system, the rate must not be more than 5000 feet for each minute.

 (b)  
When you release a vacuum from a static system, the rate must not be more than 5000 feet for each minute.

 (c)  
When you apply pressure to a pitot system, the rate must not be more than 300 knots for each minute.

 (d)  
When you release pressure from a pitot system, the rate must not be more than 300 knots for each minute.

 CAUTION: YOU MUST NOT LET THE DIFFERENCE BETWEEN THE PITOT AND
_______ STATIC PRESSURES BE MORE THAN 10.19 INCHES OF MERCURY. DAMAGE CAN OCCUR TO THE SYSTEM.
 (e)  The absolute pressure in the pitot system must be equivalent to or more than the pressure in the static system.
 CAUTION: YOU MUST NOT LET THE ABSOLUTE PRESSURE BE MORE THAN 32.10
_______ INCHES OF MERCURY. DAMAGE CAN OCCUR TO THE SYSTEM.
 (f)  
The absolute pressure applied to a static system must not be more than the ambient pressure when an instrument is connected to that static system.

 (g)  
Do not connect or disconnect the equipment when you apply a pressure or a vacuum to the pitot-static system.

 (h)  
Make sure that you flush the pitot-static probe adapter with water before installation on the probe.

 NOTE: A solution that has equal parts of ethylene glycol and
____ water must be used in temperatures between 32°F and .40°F.
 CAUTION: DO NOT APPLY ELECTRICAL POWER TO THE PITOT-STATIC PROBE
_______ HEATER. DAMAGE CAN OCCUR TO THE PITOT-STATIC PROBE.
 (i)  
Make sure that the pitot-static probe heat is off during the test.

 (j)  
Make sure that the autopilot is off.

 (k)  
Make sure that the seals used on the static ports do not extend into the static ports.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-11-00
 ALL  ú ú 02 Page 201 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 
747-400 
MAINTENANCE MANUAL
 B. C.  (l) Make sure that you do not cause damage to the surface of the static ports when you remove the seals. (m) Make sure that you install the flow restrictors between the cutoff valve and the pitot-static system.Standard Tools and Equipment (1) Adapters (a) Pitot-static probe test adapter -Rosemount Engineering, P/N 884EE with RCF kit P/N 508 or RCF Seals & Couplings, Inc., P/N 508747; (4 required) (b) Static port test adapter - NAVAIDS, P/N 33410LH-125-4 (2 required) (2) Pneumatic Test Set (a) Dry air pressure source, 30 to 35 inches of mercury (absolute) (b) Vacuum sources, 10 to 30 inches of mercury (absolute) (2 required) (3) Gages (a) Pitot system test gage - required to indicate 10 to 34 inches of mercury (absolute) with an accuracy of |0.16 (readable to |0.03) inch of mercury or |5 (readable to |1) knots. (b) Differential pressure gage - required to indicate 10 inches of mercury differential pressure (minimum) with an accuracy of |0.010 inch of mercury. (c) Static system test gage - required to indicate 10 to 30 inches of mercury (absolute) with an accuracy of |0.1 (readable to |0.01) inch of mercury or |200 (readable to |20) feet. (4) Flow restrictors, control valves, cut off valves, and pressure tape as required.Consumable Materials
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 導航 NAVIGATION 1(12)