曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (4) different steps. The first step is to disconnect all of the instruments, equipment, and drains from the pitot-static system. The second step is to seal all of the pitot-static lines. The third step is to flush each line with air. The fourth step is to put the airplane back to a satisfactory condition. A leakage test must be done on the pitot-static system where you removed the drain plugs.
 B.  Draining removes or assures the absence of liquid collected in the pitot-static system drains. Flushing removes or assures the absence of any foreign matter in the pitot-static lines.
 TASK 34-11-00-683-234
 2.  Drain Pitot-Static System_________________________
 A.  General
 (1)  The pitot-static drains are installed at these locations:
 (a)  
Some of the drains are in the left and right crawlways at STA 260 and STA 400.

 (b)  
Some of the drains are in the electrical and electronics compartment.

 (c)  
Some of the drains are in the left side of the forward cargo compartment.

 (d)  
Some of the drains are in the right side of the bulk cargo compartment.

 (e)  
Some of the drains are in section 48 below the elevator feel computer.

 B.  Standard Tools and Equipment
 (1)  Receptacle and/or absorbent cloth for collecting
 small amount of liquid from each drain

 C.  References
 (1)  34-11-00/501, Pitot-Static System
 D.  Access
 (1)  Location Zone 115 Area Between Nose Gear Well and Fuselage, LH 116 Area Between Nose Gear Well and Fuselage, RH 117 Electrical and Electronics Compartment, LH 118 Electrical and Electronics Compartment, RH 123 Forward Cargo Container Compartment, Aft Half, LH 146 Bulk Cargo Compartment, RH
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-11-00
 ALL  ú ú 01 Page 301 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 311 Area Aft of Pressure Bulkhead in Fuselage Section 48, LH
 (2)  Access Panel
 312A Access door

 E. Procedure
 S 683-A13
 (1)  Use these steps to do a visual inspection of the drain assembly shown in Fig. 301:
 (a)  
Examine the drain assembly for moisture.

 (b)  
Do steps to drain each assembly if moisture is visible.

 S 683-002
 (2)  Use these steps to drain each assembly:
 (a)  
To remove the drain cap push up and twist to release the cap from the bayonet pins.

 (b)  
Turn the drain cap and put the raised portion of the cap into the bottom of the drain body.

 (c)  
Push the cap into the drain body with hand pressure.

 (d)  
Drain all of the liquid from the sump.

 (e)  
Replace the cap on the drain body in the original position.

 (f)  
Make sure that the quick disconnect type drain cap is correctly connected.

 S 683-003
 (3)  Use these steps to drain the pitot-static lines:
 (a)  
Remove the drain plug from the drain line.

 (b)  
Let the collected liquid drain from the pitot-static line.

 (c)  
Replace the drain plug.

 TASK 34-11-00-173-235
 3.  Flush the Pitot-Static System_____________________________
 A. General
 (1)  The pitot lines can be distinguished from the static lines by color-coded quick disconnects. The red colored quick disconnects are used on the pitot systems and the yellow quick disconnects are used on the static systems.
 B. Standard Tools and Equipment
 (1)  
Dry air pressure source, 0-50 psig with filter and gage for measuring pressure

 (2)  
BACC14AD06D pressure cap (3/8") (16 required)

 (3)  
BACC14AD05D pressure cap (5/16") (4 required)

 (4)  
BACC14AD04D pressure cap (1/4") (11 required)

 (5)  
MS21913D6 plug (3/8") (27 required)

 (6)  
Protective cap (3/8") (15 required)

 (7)  
Protective cap (5/16") (9 required)

 (8)  
Protective cap (1/4") (11 required)

 (9)  
MS21902D6 union (4 required)

 (10)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 導航 NAVIGATION 1(17)