79-11-01
 ALL  ú ú N02 Page 405 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
S 024-045-N00
 (10) Remove the remaining bolts (1) which attach the oil tank (15) and the heat shield (2) to the main gearbox.
 S 024-084-N00
 CAUTION: TO PREVENT DAMAGE TO THE GEARBOX HOUSING, MAKE SURE ALL THE OIL
_______ TANK TO GEARBOX ATTACHMENT BOLTS ARE REMOVED BEFORE INSTALLING PWA 88231 PULLER.
 (11)
 Use a PWA 88231 Jackscrew Puller to carefully remove the oil tank from the gearbox as follows:

 (a)  
Put the upper clamp ring half and the lower clamp ring half
 around the oil tank between the bolt flange and the
 circumferential weld.

 (b)  
Attach the two clamp ring halves to the oil tank with the two detail socket head cap screws.

 (c)  
Tighten the two cap screws to pull the upper and lower clamp
 ring halves together.

 (d)  
Install the four detail jackscrews into the internal thread
 holes of the puller.

 (e)  
Tighten the four jackscrews slowly and equally to disengage the oil tank from the gearbox.

 (f)  
Remove the oil tank and puller from the engine.

 (g)  
Remove the puller from the oil tank. 1) Loosen and remove the two detail socket head cap screws. 2) Remove the upper and lower clamp ring halves from the oil

 tank.

 (h)  
Discard the packings (31, 32) from the oil tank (15).

 (i)  
Discard the packings (30, 33) from the check valve housing and the transfer tube.

 S 034-076-N00
 (12)
 Remove the oil quantity transmitter (AMM 79-31-01/401).

 S 034-046-N00

 (13)
 If it is necessary to replace the oil tank (15) and the detail parts are not supplied with the new oil tank, do the steps that follow:

 (a)  
Remove the clamp (14) which attaches the heat shield (2) to the oil tank (15).

 (b)  
Remove the heat shield (2).

 (c)  
Remove the bolt (11) which attaches the lanyard to the filler neck sump and valve (8).

 (d)  
Remove the oil tank cap (10) and lanyard.

 (e)  
Discard the packing (9).

 (f)  
Remove the bolts (11) which attach the filler neck sump and
 valve (8) and the scupper drain (12) to the oil tank (15).

 (g)  
Remove the filler neck sump and valve (8) and the scupper drain (12). 1) Discard the packing (7).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 79-11-01
 ALL  ú ú N02 Page 406 ú Jun 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(h)  ENGINES PRE-PW-SB 79-65;
 Do the steps that follow:

 NOTE: Oil tanks with the cutaway end do not have a sight
____
 gage.

 1) Remove the bolts (6) which attach the sight gage (5) to the oil tank (15). 2) Remove the sight gage (5). a) Discard the packing (4) and the gasket (3).
 (i)  Install the protection caps on all openings.
 TASK 79-11-01-404-021-N00
 3. Install the Oil Tank (Fig. 401)
____________________
 A. Equipment
 (1)  
M303, M305, or M307 Bergen Mechanical Crimper
 Bergen Cable Technologies Inc
 170 Gregg St

 P.O. Box 1300
 Lodi, NJ 07644-9982

 B.
Consumable Materials

 (1)  
D00390 Oil - Engine

 (2)  
G02332 Ferrule, Safety Cable (P05-292)

 (3)  
G02334 Lockwire, (P05-289) 0.032 inch (0.813 mm) - AS3214-02

 (4)  
G02335 Cable, Safety (P05-291)

 C.
Parts

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 79-11-01
 ALL  ú ú N02 Page 407 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 滑油 OIL(16)