(d)  
Install the packing (7) on the adapter (6).

 (e)  
Install the adapter (6) to the ferrule end of the No. 3 bearing oil pressure tube (9).

 (f)  
Attach the adapter (6) to the tube with bolts (5) and nuts (10). 1) Lubricate the threads of the bolts with engine oil.

 (g)  
Torque the nuts (10) that attach the adapter (6) to the ferrule end of the tube (9) to 36-40 pound-inches (4.067-4.519 newton meters). 1) Put lockwire or safety cable and safety cable ferrule on

 the bolts (5).

 (h)  
Install the oil pressure trim tube assembly (16) with the steps that follow: 1) Lubricate the tube nuts with antigallant compound. 2) Install the trim tube (16) to the oil metering nipple

 (restrictor).
 a) Tighten the tube nut with your hand.

 (i)  
Connect the manifold nuts on the No. 3 bearing oil pressure manifold (12) as follows: 1) Lubricate the manifold nut threads with antigallant

 compound (Fig. 403).
 2)  Lubricate the manifold ferrules with antigallant compound
 (Fig. 403).
 3)  Lubricate the packing with engine oil.
 4)  Install the packing and retainer to the front of the
 manifold.
 5)  Connect the front manifold nut (13) to the rear of the strainer housing on the fuel/oil cooler. a) Tighten the manifold nut with your hand.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 79-21-16
 ALL  ú ú N01 Page 418 ú Jun 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
6) Tighten the nut on the oil pressure trim tube (16) to the
 manifold tee (12) with your hand.
 7) Connect the rear manifold nut (13) to the adapter in the
 No. 3 bearing oil pressure tube (9).
 NOTE: The rear manifold nut is at the 9 o'clock position.____
 a) Tighten the manifold nut with your hand.
 (j)  Attach the ferrule end of the No. 3 bearing oil pressure tube
 (9) to the bracket on Flange K with two bolts (11).
 1) Lubricate the bolt threads with engine oil.
 (k)  Torque the bolts to 36-40 pound-inches (4.067-4.519 newton
 meters).
 (l)  Adjust the forward tube clamp (14) on the oil trim pressure
 tube (16) and the clamp on the No. 3 bearing oil pressure
 manifold (12).
 NOTE: Adjust the clamps until the center of the forward clamp____
 (on the oil trim pressure tube) is 2.500-3.000 inch
 (63.500 - 76.200 milimeters) from the center of the rear
 clamp.
 (m)  Attach the clamps (14) together with a bolt (17) and nut (15).
 1) Lubricate the threads of the bolt with engine oil.
 2) Torque the bolt to 36-40 pound-inches (4.067-4.519 newton

 meters).
 CAUTION: YOU MUST USE THE WRENCHING FLATS ON THE PARTS THAT ARE
_______ CONNECTED WHEN YOU TIGHTEN MANIFOLDS AND TUBES. IF YOU DO NOT DO THIS, YOU CAN TWIST THE TUBE AND CAUSE DAMAGE TO THE TUBE.
 (n)  Torque the manifold nuts on the No. 3 bearing oil pressure manifold (12) as follows: 1) Torque the front manifold nut that is attached to the
 strainer housing on the fuel/oil cooler to 140-160 pound-inches (15.818-18.078 newton meters). a) Loosen the same front manifold nut.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 79-21-16
 ALL  ú ú N01 Page 419 ú Jun 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
b)  Torque the front manifold nut again to the same torque value, 140-160 pound-inches (15.818-18.078 newton meters).
 2)  Torque the rear manifold nut to the adapter in the No. 3 bearing oil pressure tube to 675-750 pound-inches (76.265-84.739 newton meters)
 3)  Install lockwire or safety cable and safety cable ferrule to the manifold nuts.
 (o)  Torque the tube nuts on the oil trim pressure tube (16) as follows: 1) Torque the front tube nut that is attached to the manifold
 tee to 675-750 pound-inches (76.265-84.739 newton meters).
 2)  Torque the tube nut that is attached to the oil tube metering nipple (restrictor) to 675-750 pound-inches (76.265-84.739 newton meters).
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 滑油 OIL(93)