(a)  
Make sure the inner slotted holes for the inlet collars (13)
 align with the bolts with the captive washers (4).

 S 644-059-N00
 (11)
 Lubricate the threads of the bolts (2) with engine oil.

 S 434-034-N00

 (12)
 Attach the forward hinge bracket (19) with the bolts (2) and washers (28) to the intermediate case.

 (a)  
Tighten the bolts (2) with your hand.

 S 644-060-N00
 (13)
 Lubricate the threads of the bolts (16) with engine oil.

 S 434-035-N00

 (14)
 Attach the higher and lower mounting brackets (29, 21) to the support brackets for the intermediate case with the bolts (16).

 (a)  
Tighten the bolts (16) with your hand.

 (15)
 Lubricate the threads of the bolt (22) with engine oil.

 S 434-036-N00

 (16)
 Attach the cable conduit to the lower support bracket with the bolt (22).

 (a)  
Tighten the bolt (22) to 36-40 pound-inches
 (4.1-4.5 newton-meters).

 (b)  
ENGINES PRE-PW-SB 79-60; Attach the valve inlet collars to the rear of the intermediate case as follows:

 S 644-061-N00
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 79-21-09
 ALL  ú ú N01 Page 418 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
1)  Install the outboard bolts (2) with washers (3), in the outboard holes. Lubricate the threads with engine oil. a) Tighten the four inboard bolts (4) by hand. These are
 the bolts that were installed before the four outboard bolts.
 (c)  ENGINES POST-PW-SB 79-60;
 Attach the valve inlet collars (13) to the rear of the
 intermediate case as follows:
 1) Install the four bolt and washer assemblies (2) in the

 outboard bolt holes. Lubricate the threads with engine oil. 2) Tighten the four inboard bolt and washer assemblies (4) by hand.
 NOTE: These are the bolt and washer assemblies that were
____ installed before the four outboard bolt and washer assemblies.
 S 434-038-N00
 CAUTION: WHEN YOU USE A TORQUE ADAPTER, YOU MUST ADJUST THE TORQUE
_______ WRENCH VALUE TO GET THE NECESSARY TORQUE (AMM 70-23-00/201). IF THE INCORRECT TORQUE IS APPLIED TO THE BOLT, IT CAN CAUSE DAMAGE TO THE THREADS.
 (17) Tighten the bolts (2, 4) or bolt and washer assemblies to 85-95 pound-inches (9.6-10.7 newton-meters).
 NOTE: Use the PWA 85853 torque adapter to tighten the inner bolts.
____
 S 434-040-N00
 (18)
 Tighten the bolts (16) to 85-95 pound-inches (9.6-10.7 newton-meters).

 (19)
 Lubricate the packings (11) with engine oil.

 S 434-041-N00

 (20)
 Install the packings (11) to the two ends of the oil inlet tube (9) and to the oil outlet tube (8).

 S 434-074-N00

 (21)
 Move the oil inlet tube (9) forward to connect it to the air/oil heat exchanger (1).

 S 434-054-N00

 (22)
 Move the aft end of the oil inlet tube (9) down to connect the other end to the housing of the main oil filter.

 S 644-063-N00
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 79-21-09
 ALL  ú ú N01 Page 419 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
S 644-064-N00
 (23)
 Lubricate the threads of the bolts (12) with engine oil.

 S 434-065-N00

 (24)
 Attach the aft end flange to the housing with the bolts (12).

 (a)  
Tighten the bolts (12) to 85-95 pound-inches (9.6-10.7 newton-meters).

 S 434-042-N00
 (25)
 Connect the oil outlet tube (8) to the air/oil heat exchanger (1).

 S 644-066-N00

 (26)
 Lubricate the threads of the bolts (10) with engine oil.

 S 434-043-N00

 (27)
 Attach the collars for the oil inlet tube (9) and the oil outlet tube (8) to the air/oil heat exchanger (1) with the bolts (10).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 滑油 OIL(70)