(a)  If a plastic protective disk is ejected from the disk drive, then remove it.
 S 862-021
 (6)  
Close this circuit breaker:

 (a)  On the P11 panel:
 1) 11F23, DATA LOADER

 (7)  
Wait until the display shows INSERT DISK #1.

 S 862-022
 NOTE: The display lights and the ADL FAIL light will go on and
____ off while the ADL does a self test. When the self test is complete, the display will show INSERT DISK #1.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-15-11
 ALL  ú ú 01 Page 212 ú Jan 28/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL

 S 862-023
 (8)  
Make sure that the circuit breakers are closed for the applicable component or system that will receive the new software.

 S 422-024

 (9)  
Do these steps at the ADL to install the software:

 NOTE: You must know the correct software part numbers for the
____ component. For the component to be an approved installation, software with the correct part numbers must be installed.
 NOTE: This is a general procedure for software installation.
____ Some components have other steps that are necessary. The software installation task for the component will include all necessary steps.
 (a)  
Set the switch or switches on the data loader control panel to the applicable position for your component or system.

 (b)  
Carefully push the first disk (label up) into the disk drive.

 NOTE: The display will show DISK INSERTED and then VOL:.
____ If the destination component is active, the display will then show the file, extension and the percent of the file transfer completed. If there is more than one file, the ADL will install the next file until all files are completed. If the software is on more than one disk, then the display will show CHANGE DISK or INSERT DISK when it is time to put in the subsequent disk.
 NOTE: If TRANSFER FAIL shows, then the installation is
____ not completed. Open and close the circuit breaker for the component, and start the installation again.
 IF READ/WRITE FAIL shows, then there is a problem with the disk. Open and close the circuit breaker for the component, and start the installation again. If the problem continues, then replace the disk.
 (c)  If CHANGE DISK or INSERT DISK shows on the display, wait approximately 10 seconds and then push the eject button.
 NOTE: The installation can fail if you wait too long
____ before you remove and install disks.
 1) Remove the disk from the disk drive. 2) Put the subsequent disk into the disk drive. 3) If there are more than two disks for the software
 installation, then remove and install disks until LOAD COMPLETE shows on the display.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-15-11
 ALL  ú ú 01 Page 213 ú Jan 28/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
 (d)  
When LOAD COMPLETE shows on the display, wait approximately 10 seconds and then push the eject button.

 (e)  
Remove the disk from the disk drive.

 (f)  
If there was a plastic protective disk in the disk drive before you installed software, then put it back in the disk drive.

 S 862-025
 (10)
 Set the system select switch on the data loader control panel to the NORMAL position.

 S 412-026

 (11)
 Close the front cover on the ADL.

 S 742-027

 (12)
 Make sure that the correct software part numbers are installed in the component.

 NOTE: The software installation task for the component has the
____ steps to do a software configuration check.
 S 862-045
 (13) Remove electrical power (AMM 24-22-00/201).
 E. SFIM Airborne Data Loader Procedure
 S 862-043
 (1)  Supply electrical power (AMM 24-22-00/201).
 (a)  Make sure that the power is not removed while you install software.
 NOTE: A power interruption will cause a failure of the
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 STANDARD PRACTICES - AIRFRAME(95)