曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

8 --36  11.1  1.2541313  13.2  1.4913994  14.8  1.6721750  17.6  1.9885325 
10 --24  11.8  1.3332206  13.7  1.5478918  15.7  1.7738614  18.2  2.0563234 
10 --32  16.4  1.8529507  19.0  2.1467112  21.3  2.4065762  24.8  2.8020230 
1/4 --20  38.8  4.3838102  45.1  5.0956145  51.7  5.8413142  60.1  6.7903865 
1/4 --28  48.5  5.4797628  56.4  6.3723427  64.7  7.3101166  75.2  8.4964570 
5/16 --18  69.7  7.8750406  79.4  8.9709931  92.9  10.4962879  105.6  11.9311949 
5/16 --24  75.0  8.4738600  85.2  9.6263050  100.0  11.2984800  113.6  12.8350733 
3/8 --16  124.6  14.0779061  141.6  15.9986477  166.0  18.7554768  188.0  21.2411424 
3/8 --24  136.7  15.4450222  155.4  17.5578379  182.0  20.5632336  207.0  23.3878536 
* Minimum torque values for bolt and nuts used for sealing joints with diaphragms or gaskets.  If, however, sealing is not complete, retorquing is allowed to a higher value in accordance with paragraph 5 C. However, torques used shall not exceed the value of steel or CRES bolts and nuts, whichever is applicable as shown in Table 505. 
Page 514 Apr 1/05 Copying, use or disclosure of information on this page is subject to proprietary restrictions.

Assembly
20-00-02/70-00-01

C. Guideline - Assembly Torque Values (Nuts, Bolts, Screws, Studs, and Inserts)
NOTE:  Table 507, Table 508, and Table 509 list assembly torque values based on service requirements for A286 heat-resisting alloy steel or equivalent fastener material with lubricated threads.
Torque values specified are in addition to frictional torques developed by self-locking devices.
Unless specified otherwise in tables, use nominal values as follow:
.  
250 inch-pounds, ±5% (0 - 28.2462 N-m)

.  
1200 inch-pounds, ±2.% (28.2462 - 135.58176 N-m)

.  
Over 1200 inch-pounds, ±1% (Over 135.58176 N-m)

NOTE:  Where two torque values are included, use the smaller one when the nut is torqued and the bolt is held stationary. Use the larger value when the bolt is torqued and the nut is held stationary.
Studs which have a different thread size on opposite ends shall be torqued to the smaller size regardless of which end is fitted into the installation.
When the use of Hylomar is specified, multi-bolted flanges shall be retorqued to original values after a 10-minute waiting period.
Application examples for Table 507, Table 508, and Table 509 torque values follow.
.  
Table 507-Highly loaded connections; generally in specialized regions of the turbine such as steel-to-steel environment or joints directly exposed to rotor bearing dynamic forces. Specific applications include.

. Turbine plenum-diffuser flanges
. Turbine plenum-bearing flanges
. Turbine stator flanges
. Turbine bearing carrier-bearing capsule flanges

.  
Table 508-Moderately loaded connections; generally aluminum joints, magnesium joints, aluminum or magnesium-to-steel joints in the compressor, gearbox, or accessory region of gas turbines.  Some specific applications are.

. Diffuser-gearbox flanges
. Accessory cases-gearbox flanges
. Mounting flanges for accessories gearing
. Compressor, diffuser, and shroud flanges

.  
Table 509—Lightly loaded connections; generally for clips and brackets.  Torques may be used for nuts and a bolt installed on key- or ring-locked studs or inserts in magnesium for lightly loaded joints.
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：標(biāo)準(zhǔn)施工手冊 STANDARD PRACTICES MANUAL 20-00-02/70-00-01(110)