Repair
20-00-02/70-00-01

Table 402. Dimension and Installation Data for Heavy Duty Keensert Thread Inserts (Cont)

Repair Page 434 Apr 1/05
20-00-02/70-00-01
Table 403.  Dimension and Installation Data for Light Weight Keensert Thread Inserts
DIMENSIONS  INSTALLATION DATA  REMOVAL   DATA 
Non-Locking  Internal Thread Locking  Internal Thread Class 3B  External Thread  *L  *A  Tap Drill  Dia  C'Sink Dia   +.010   -.000  Thread Tap  Drill 
Size Class 2A  Shear Engag.  Size Class 2B  Min Depth  Installation Tool Part Number  Size  Depth 
X  10-32  5/16-18  .1517  .31  .272  .323  5/16-18  .37  TD 1032L  7/32  5-32 
X  .0945  .31 
X  10-24  .1517  TD 1024L 
X  .0945  .31 
X  1/4-28  3/8-16  .2371  .37  .332  .385  3/8-16  .43  TD 428L  9/32  3/16 
X  .1726  .33 
X  1/4-20  .2371  TD 420L 
X  .1726  .36 
X  5/16-24  7/16-14  .3049  .43  .397  .447  7/16-14  .50  TD 524L  11/32 
X  .2321  .34 
X  5/16-18  .3049  TD 518L 
X  .2321  .37 
X  3/8-24  1/2-13  .4299  .50  .453  .510  1/2-13  .56  TD 624L  13/32 
X  .3366  .36 
X  3/8-16  .4299  TD 616L 
X  .3366  .40 
X  7/16-20  9/16-12  .5665  .56  .516  .572  9/16-12  .62  TD 720L  15/32 
X  .4606  .41 
X  7/16-14  .5665  TD 714L 
X  .4606  .45 
X  1/2-20  5/8-11  .7175  .62  .578  .635  .68  TD 820L  17/32 
X  .5906  .42 
X  1/2-13  .7175  TD 813L 
X  .5906  .47
            L = Lenth of external threads   A= Maximum distance to then of thread lock.with internal thread size 5/16 and more are furnished with 4 locking Kees. STANDARD MATERIALS:  INSERT - 303 CRES (passivated)                        Kees - 302 CRES        Inserts 

Repair
Page 435 Apr 1/05 Copying, use or disclosure of information on this page is subject to proprietary restrictions.
20-00-02/70-00-01

B.  Method No. 407B: Loose or Damaged Thread Inserts (Aluminum or Magnesium Parts) Replacement
Replace loose or damaged thread inserts in aluminum or magnesium-alloy parts as follows:
(1)  
Use long-nosed pliers (SECTION VII) to remove loose or damaged inserts.

WARNING: SOLVENT VAPORS ARE TOXIC AND FLAMMABLE.  DO NOT INHALE
VAPORS. OBSERVE FIRE PRECAUTIONS.

(2)  
Clean hole from which insert was removed, using solvent (Federal Specification P-D-680, Type 1) (SECTION VII) and remove corrosion if present.

NOTE:  Refer to applicable manual to verify type of primer required.

(3)  
Apply a thin, even coat of primer (Type I, Class C) (SECTION VII) to threaded area in which new insert is to be installed.

NOTE:  Use a modified screwdriver, or a rod, with the correct outside diameter to fit inside diameter of insert and slotted to fit over tang of insert, to install new insert.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：標準施工手冊 STANDARD PRACTICES MANUAL 20-00-02/70-00-01(81)