71-00-02
 

Hydraulic and Fuel Plumbing Installation
Figure 5-2 (Sheet 6)

71-00-02
 

ITEM NO.  PART NUMBER  NOMENCLATURE  UC  QTY 
5-2  HYDRAULIC AND FUEL PLUMBING INSTALLATION (FIGURE 5-2, SHEET 6) SECURE TUBE ASSEMBLIES (80, 100, 105) TO THE FAN CASE USING ITEMS (165 THRU 185). 
165  332N3101-5  . CLAMP BLOCK HALVES  2 
170  332N3101-6  . CHANNEL  1 
175  BACS12HN3U47  . SCREW  3 
180  NAS1149C0332R  . WASHER  3 
185  NAS43DD3-147FC  . SPACER SECURE TUBE ASSEMBLY (110) TO THE FAN CASE USING ITEMS (190 THRU 215).  3 
190  332N3101-1  . CLAMP BLOCK HALVES  2 
195  332N3101-2  . CHANNEL  1 
200  BACS12HN3U39  . SCREW  2 
210  NAS1149C0332R  . WASHER  2 
215  NAS43DD3-114FC  . SPACER SECURE TUBE ASSYS (100) TO TUBE ASSY (105) USING ITEMS (220 THRU 241).  2 
220  BACC10GE21  . CLAMP  2 
221  BACC10GT2-20  . CLAMPSHELL  4 
225  BACC10GE8  . CLAMP  2 
226  BACC10GT2-08  . CLAMPSHELL  4 
230  BACS12HN3U9  . SCREWS  2 
235  NAS1149C0332R  . WASHER  2 
240  BACN10YR3C  . NUT  2 
241  BACS18AF  . SPACER (SEE INTRODUCTION) PLACE NON-ILLUSTRATED O-RING (-250) IN BAG AND ATTACH TO TUBE ASSEMBLY (80).  AR 
-250  MS29513-131  . O-RING  1 

71-00-02
 
PW2000 SERIES ENGINES

757
POWERPLANT BUILDUP MANUAL

FIGURE 6-1
THIS FIGURE NOT USED

REF DWG: 332N3100
71-00-02
P/P BUILDUP FIGURE 6-1 Page 1 May 05/2009
 
PW2000 SERIES ENGINES

757
POWERPLANT BUILDUP MANUAL

THIS FIGURE NOT USED
Figure 6-1 (Sheet 1)

71-00-02
P/P BUILDUP FIGURE 6-1 Page 2 Jan 15/2011
 

ITEM NO.  PART NUMBER  NOMENCLATURE  UC  QTY 
6-1  THIS FIGURE NOT USED (FIGURE 6-1, SHEET 1) THIS SHEET NOT USED 

71-00-02
 
PW2000 SERIES ENGINES

757
POWERPLANT BUILDUP MANUAL

FIGURE 6-2
INTEGRATED DRIVE GENERATOR
INSTALLATION

REF QEC TASK NO.: 6
REF DWG: 332N3240

71-00-02
P/P BUILDUP FIGURE 6-2 Page 1 May 05/2009
 

Integrated Drive Generator Installation
Figure 6-2 (Sheet 1)

71-00-02
 

ITEM NO.  PART NUMBER  NOMENCLATURE  UC  QTY 
6-2  INTEGRATED DRIVE GENERATOR INSTALLATION (FIGURE 6-2, SHEET 1) CAUTION: KEEP GREASE OUT OF DOWEL PIN AND BOLT HOLES. GREASE BUILD-UP IN HOLES MAY CAUSE DAMAGE TO GEARBOX DUE TO PRESSURE BUILDUP WHEN BOLTS ARE INSTALLED. APPLY A COATING OF DOW CORNING NO. 4 SILICONE GREASE TO ADAPTER (10), GEARBOX PAD, AND SCREW THREADS (15). ALIGN MARKS ON ADAPTER (10) AND GEARBOX PAD. INSTALL ADAPTER (10) AND GASKET (11) ON GEARBOX AND SECURE WITH SCREWS (15). TIGHTEN TO 276-300 LB-IN. 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 動力裝置安裝手冊 Powerplant Buildup Manual(67)