曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

design selection or to reduce the associated risk to an acceptable level with safety and warning
devices, incorporate special procedures and training. Procedures may include the use of personal
protective equipment. For hazards assigned Catastrophic or Critical mishap severity categories,
avoid using warning, caution, or other written advisory as the only risk reduction method.
4.5 Reduction of mishap risk to an acceptable level. Reduce the mishap risk through a
mitigation approach mutually agreed to by both the developer and the program manager.
Communicate residual mishap risk and hazards to the associated test effort for verification.
4.6 Verification of mishap risk reduction. Verify the mishap risk reduction and
mitigation through appropriate analysis, testing, or inspection. Document the determined
residual mishap risk. Report all new hazards identified during testing to the program manager
and the developer.
4.7 Review of hazards and acceptance of residual mishap risk by the appropriate
authority. Notify the program manager of identified hazards and residual mishap risk. Unless
otherwise specified, the suggested tables A-I through A-III of the appendix will be used to rank
residual risk. The program manager shall ensure that remaining hazards and residual mishap risk
are reviewed and accepted by the appropriate risk acceptance authority (ref. table A-IV). The
appropriate risk acceptance authority will include the system user in the mishap risk review. The
appropriate risk acceptance authority shall formally acknowledge and document acceptance of
hazards and residual mishap risk.
4.8 Tracking of hazards, their closures, and residual mishap risk. Track hazards, their
closure actions, and the residual mishap risk. Maintain a tracking system that includes hazards,
their closure actions, and residual mishap risk throughout the system life cycle. The program
manager shall keep the system user advised of the hazards and residual mishap risk.
5. DETAILED REQUIREMENTS
Program managers shall identify in the solicitation and system specification any specific system
safety engineering requirements including risk assessment and acceptance, unique classifications
and certifications (see 6.6 and 6.7), or any mishap reduction needs unique to their program.
Additional information in developing program specific requirements is located in Appendix A.
MIL-STD-882D
5
6. NOTES
(This section contains information of a general or explanatory nature that may be helpful, but is
not mandatory.)
6.1 Intended use. This standard establishes a common basis for expectations of a
properly executed system safety effort.
6.2 Data requirements. Hazard analysis data may be obtained from contracted sources
by citing DI-MISC-80508, Technical Report - Study/Services. When it is necessary to obtain
data, list the applicable Data Item Descriptions (DIDs) on the Contract Data Requirements List
(DD Form 1423), except where the DoD Federal Acquisition Regulation Supplement exempts
the requirement for a DD Form 1423. The developer and the program manager are encouraged
to negotiate access to internal development data when hard copies are not necessary. They are
also encouraged to request that any type of safety plan required to be provided by the
contractor, be submitted with the proposal. It is further requested that any of the below listed
data items be condensed into the statement of work and the resulting data delivered in one
general type scientific report.
Current DIDs, that may be applicable to a system safety effort (check DoD 5010.12-L,
Acquisition Management Systems and Data Requirements Control List (AMSDL) for the most
current version before using), include:
DID Number DID Title
DI-MISC-80043 Ammunition Data Card
DI-SAFT-80101 System Safety Hazard Analysis Report
DI-SAFT-80102 Safety Assessment Report
DI-SAFT-80103 Engineering Change Proposal System Safety Report
DI-SAFT-80104 Waiver or Deviation System Safety Report
DI-SAFT-80105 System Safety Program Progress Report
DI-SAFT-80106 Occupational Health Hazard Assessment
DI-SAFT-80184 Radiation Hazard Control Procedures
DI-MISC-80508 Technical Report - Study Services
DI SAFT-80931 Explosive Ordnance Disposal Data
DI-SAFT-81065 Safety Studies Report
DI-SAFT-81066 Safety Studies Plan
DI-ADMN-81250 Conference Minutes
DI-SAFT-81299 Explosive Hazard Classification Data
DI-SAFT-81300 Mishap Risk Assessment Report
DI-ILSS-81495 Failure Mode, Effects, Criticality Analysis Report
MIL-STD-882D
6
6.3 Subject term (key word) listing.
Environmental
Hazard
Mishap
Mishap probability levels
Mishap risk
Mishap severity categories
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：System Safety Handbook系統安全手冊下(114)