曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

the GPS circuit-breaker to the GPS receiver. Refer to Chapter 92 for the wiring diagrams.
Every 28 days, Bendix/King receives new data base information. This information is downloaded
onto data base cards. The data base card is inserted in the slot on the left side of the GPS receiver.
There are three data base coverage areas available for the KLN 89B. They are known as the
'Americans' data base, the 'Atlantic' data base, and the 'Pacific' data base.
The KLN 89B GPS receiver has these controls:
) ON-OFF knob. It is used to turn the unit on and off.
) Right outer knob. When the cursor is off, it is used to select the page type (for example, APT,
NAV, FPL, etc.). When the cursor is on, it is used to move the cursor on the display.
) Right inner knob - When the cursor is off, it is used to select the specific page number for a
page type (for example, APT 1, APT 2, APT 3, etc.). When the cursor is on, it is used to select
alphanumerics or other applicable data for the field the cursor is on.
) CRSR (cursor) button. It is used to turn the cursor on and off.
) MSG (message) button. It is used to view messages.
) OBS button. It is used to select between LEG mode and OBS modes.
) ALT (altitude) button. It is used to select the two Altitude Pages where baro settings are made
and VNAV operation is set up.
) NRST (nearest) button. It is used to bring up a menu of nearest functions (Airports, VOR's,
NDB's, intersections, etc.) that may be selected.
) Dº (direct-to) button. It is used to initiate 'direct-to' operation (navigation from the present position
direct to the destination).
) CLR (clear) button. It is used to delete data from a data field.
) ENT (enter) button. It is used to approve or acknowledge data.
AIRCRAFT
Navigation
DA 40 Series
AMM
Page 4
20 Sep 2007 34-58-00 Doc # 6.02.01
Rev. 5
Figure 2: Bendix/King KLN 94 GPS receiver
AIRCRAFT
DA 40 Series
AMM
Navigation
Doc # 6.02.01
Rev. 5 34-58-00 Page 5
20 Sep 2007
B. Bendix/King KLN 94 GPS Receiver
Figure 2 shows the Bendix/King KLN 94 GPS receiver. It is located in the avionics rack in the
instrument panel, see Chapter 31.
The avionics bus or, if installed, the essential avionics bus supplies power to the GPS receiver. The
ALT/BAT switch and the AVIONICS MASTER switch must be set to ON to supply power through
the GPS circuit-breaker to the GPS receiver. Refer to Chapter 92 for the wiring diagrams.
Every 28 days, Bendix/King receives new data base information. This information is downloaded
onto data base cards. The data base card is inserted in the slot on the left side of the GPS receiver.
There are three data base coverage areas available for the KLN 94. They are known as the
'Americans' data base, the 'Atlantic' data base, and the 'Pacific' data base.
The KLN 94 GPS receiver has these controls:
) ON/OFF/brightness knob. It is used to turn the unit on and off and adjust display brightness.
) Right outer knob. When the cursor is off, it is used to select the page type (for example, APT,
NAV, FPL, etc.). When the cursor is on, it is used to move the cursor on the display.
) Right inner knob - When the cursor is off, it is used to select the specific page number for a
page type (for example, APT 1, APT 2, APT 3, etc.). When the cursor is on, it is used to select
alphanumerics or other applicable data for the field the cursor is on.
) PROC (procedure) button. It is used to initiate the loading of approaches, arrival procedures,
and departure procedures. Also used to activate vector-to-final (VTF) for approaches when an
approach with 'Vectors' has been loaded into the active flight plan.
) RNG (range) button. It is used to change the map scale if the map page (Nav 4) page is being
displayed. It is used to select the map page if it is not already on the map page.
) MEN (menu) button. It is used to display the map menu if the map page (Nav 4) page is being
displayed. The map menu is used to initiate changing what is displayed on the map as well as
select the map orientation. It is used to select the map page if it is not already on the map page.
) CRSR (cursor) button. It is used to turn the cursor on and off.
AIRCRAFT
Navigation
DA 40 Series
AMM
Page 6
20 Sep 2007 34-58-00 Doc # 6.02.01
Rev. 5
) MSG (message) button. It is used to view messages.
) OBS button. It is used to select between LEG mode and OBS modes.
) ALT (altitude) button. It is used to select the two Altitude Pages where baro settings are made
and VNAV operation is set up.
) NRST (nearest) button. It is used to bring up a menu of nearest functions (Airports, VOR's,
NDB's, intersections, etc.) that may be selected.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石40系列AMM 2(100)