曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

you will remove.
Refer to Section 12-10.
(2) Remove the wing that has the fuel tank probe that
you will remove, and support the wing on trestles.
Refer to Section 57-10.
(3) Remove the fuel tank assembly from the wing. Refer to Section 28-10.
(4) Remove the probe from the threaded mounting.
B. Install the Fuel Tank Probe to the Inboard Fuel Chamber
Detail Steps/Work Items Key Items/References
(1) Split inboard fuel chamber from outboard fuel
chamber.
Refer to Section 28-10.
(2) Install the probe into the inboard fuel chamber:
S Apply sealant to the thread of the probe.
% S Install the Teflon sleeve to the probe.
S Carefully move the probe into position in the
inboard chamber. Engage the thread.
S Turn the probe clockwise, by hand, until the
probe is fully engaged in its mount.
S Tighten the probe.
Use 'seal-lube' or 'fuel-lube'.
Ensure that the probe goes into the guide
at the outboard end of the fuel chamber.
Torque 26 Nm (19.2 ft.lb).
(3) Re-connect inboard fuel chamber to outboard fuel
chamber.
Refer to Section 28-10.
(4) Install the fuel tank assembly into the wing. Refer to Section 28-10.
(5) Install the wing to the airplane. Refer to Section 57-10.
(6) Refuel the airplane. Refer to Section 12-10.
(7) Examine the fuel probe installation for fuel leaks.
(8) Install the access panel for the fuel tank. Refer to Section 52-40.
C. Remove the Fuel Tank Probe from the Long Range Fuel Chamber
AIRCRAFT
Fuel System
DA 40 Series
AMM
Page 204
20 Sep 2007 28-40-00 Doc # 6.02.01
Rev. 5
The long range fuel chamber is part of the Long Range Tank (OÄM 40-071).
Detail Steps/Work Items Key Items/References
(1) Defuel the wing that has the fuel tank probe that
you will remove.
Refer to Section 12-10.
(2) Remove the wing that has the fuel tank probe that
you will remove, and support the wing on trestles.
Refer to Section 57-10.
(3) Remove the fuel tank assembly. Refer to Section 28-10.
(4) Disassemble the fuel tank assembly. Refer to Section 28-10.
(5) Remove the long range fuel probe from the
threaded mounting.
D. Install the Fuel Tank Probe to the Long Range Fuel Chamber
The long range fuel chamber is part of the Long Range Tank (OÄM 40-071).
Detail Steps/Work Items Key Items/References
(1) Install the probe into the long range fuel chamber:
S Apply sealant to the thread of the probe.
% S Install the Teflon sleeve to the fuel probe.
S Carefully move the probe into position in the
long range fuel chamber. Engage the thread.
S Turn the probe clockwise, by hand, until the
probe is fully engaged in its mount.
S Tighten the probe.
Use 'seal-lube' or 'fuel-lube'.
Ensure that the probe goes into the
guide at the outboard end of the fuel
chamber.
(2) Assemble the fuel tank assembly. Refer to Section 28-10.
(3) Install the fuel tank assembly. Refer to Section 28-10.
(4) Install the wing to the airplane. Refer to Section 57-10.
(5) Refuel the airplane. Refer to Section 12-10.
(6) Examine the fuel probe installation for leaks.
(7) Install the access panel for the fuel tank. Refer to Section 52-40.
AIRCRAFT
DA 40 Series
AMM
Fuel System
Doc # 6.02.01
Rev. 5 28-41-00 Page 1
20 Sep 2007
Section 28-41
Fuel Quantity Indicating - TAE 125 Diesel Engine
1. General
This Section tells you about the fuel quantity indicating system of the DA 40 with the TAE 125 Diesel
engine installed. Refer to Section 28-01 for the general data on the fuel system. Refer to Section 31-11
for data on replacing the fuel quantity indicator.
2. Description
Figure 1 shows the fuel quantity indication system main components. The fuel quantity indication
% system is part of the engine indicating system. The fuel tank in each wing has a fuel probe with a Teflon
% sleeve on the outboard end. The fuel quantity indicating system cannot be calibrated in service.
Electric cables connect the fuel probes to the engine indicating system. The system displays the fuel
quantity on the Auxiliary Engine Display (AED) located in the right instrument panel.
Electric cables also connect the low fuel sensor in the left tank to a low fuel caution light in the
annunciator panel. Refer to Section 31-51 for more data on the annunciator panel.
3. Operation
As the fuel level in the fuel tanks decreases, the area of the fuel probe which is “wetted” with fuel will
also decrease. The amount of "wetted" area is converted into an electrical signal which sets the fuel
quantity reading at the fuel quantity indicator. The fuel quantity indicator displays the quantity of fuel
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石40系列AMM 2(36)