曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Structures
Doc # 6.02.01
Rev. 5 51-60-00 Page 11
20 Sep 2007
Pivot Axis
Moment Arm
Moment Arm
Pivot Axis
Horizontal
Spring
Balance
Tape
Refer to Figure 1 (Standard Tanks) or Figure 2 (Long Range Tanks) for the weight and residual
% moment for the DA 40. Refer to Figure 3 for the weight and residual moment for the DA 40 D.
Use any suitable method to support the trim tab horizontally at the pivot axis.
The trim tab must be able to rotate freely around the pivot axis.
The residual moment is tail heavy.
% Figure 6: Trim Tab Static Balance
AIRCRAFT
Standard Practices and
Structures
DA 40 Series
AMM
Page 12
20 Sep 2007 51-60-00 Doc # 6.02.01
Rev. 5
Mass Balance
Moment Arm
Pivot Axis
Horizontal
Mass Balance Weight
Pivot
Axis
Moment
Arm
Spring
Balance
Tape
Refer to Figure 1 (Standard Tanks) or Figure 2 (Long Range Tanks) for the weight and residual
% moment for the DA 40. Refer to Figure 3 for the weight and residual moment for the DA 40 D.
Use any suitable method to support the aileron horizontally at the pivot axis.
The aileron must be able to rotate freely around the pivot axis.
The balance includes the horn, trim plate and hinges.
%
%
%
% Figure 7: Aileron Static Balance
AIRCRAFT
DA 40 Series
AMM
Standard Practices and
Structures
Doc # 6.02.01
Rev. 5 51-60-00 Page 13
20 Sep 2007
Pivot
Axis
Moment Arm
Spring
Balance
Mass Balance Weight
Moment Arm
Mass Balance Weight Pivot Axis
Horizontal
Refer to Figure 1 (Standard Tanks) or Figure 2 (Long Range Tanks) for the weight and residual
% moment for the DA 40. Refer to Figure 3 for the weight and residual moment for the DA 40 D.
Use any suitable method to support the wing flap horizontally at the pivot axis.
The wing flap must be able to rotate freely around the pivot axis.
The balance includes the horn and hinges.
The residual moment is tail heavy.
% Figure 8: Wing Flap Static Balance
AIRCRAFT
Standard Practices and
Structures
DA 40 Series
AMM
Page 14
20 Sep 2007 51-60-00 Doc # 6.02.01
Rev. 5
% Intentionally left blank
AIRCRAFT
DA 40 Series
AMM
Standard Practices and
Structures
Doc # 6.02.01
Rev. 5 51-80-00 Page 1
20 Sep 2007
Section 51-80
Electrical Bonding
1. General
The bonding system gives the airplane good lightning protection. A special bonding system is
necessary for the composite structure of the DA 40. Without this special system, the composite
structure would not sufficiently conduct electricity.
Refer to Section 21-60 for details about the static discharge wicks.
2. Description
Figure 1 shows a simplified bonding system schematic.
The lightning conductor system is the main part of the bonding system. High capacity aluminum alloy
tubes and strips make the lightning conductor system.
The lightning conductor system has a longitudinal branch and a lateral branch. The longitudinal branch
runs from the engine block via engine truss, firewall, cabin, aft fuselage and empennage to the
elevator. The horizontal branch connects the left wing tip with the right wing tip. It is connected with
the longitudinal branch at the cabin floor under the forward seats.
Metal braiding and strips connect all conductive components (for example: wing skin, fuel tanks,
control systems, landing gear, engine, etc.) and antenna ground plates to the lightning conductor
system.
AIRCRAFT
Standard Practices and
Structures
DA 40 Series
AMM
Page 2
20 Sep 2007 51-80-00 Doc # 6.02.01
Rev. 5
Trim System
Bracket
Lightning
Electrode
Horizontal
Stabilizer
Rudder
Bracket
Horizontal
Stabilizer
Main Brackets
Vertical
Tube
Pitot
Probe
Aileron
Lever
Fuel
Tank
Landing
Gear LH
Landing
Gear RH
Step
Step
Com
Antenna
Top
Bottom
Com.
Antenna
ADF Antenna
Flaps Crosstube
Marker
Antenna
CF Frame
CF Frame
GPS Antenna
Cabin Door Hinge
Engine
Top
Cowl
Engine Top
Cowl
Canopy Hinge RH
Canopy
Hinge LH
Canopy Horn
Engine
Mounting
Bolt
Engine
Mounting
Bolt
Nose
Gear
Ground
Ground
Bus
Canopy
Horn
Engine Mount
.
Figure 1: Airplane Lightning Protection and Bonding System Schematic
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石40系列AMM 2(123)