曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

be set to ON to supply power through the 'WX-500'-circuit breaker to the Stormscope system.
The processor houses the lightning data acquisition circuitry as well as the circuitry necessary to
process heading information and communicate with the host MFD (Bendix/King KMD 150 or
Garmin GNS 430/530, refer to Section 34-58). All WX-500 functions are controlled through the MFD
% or the GNS 430.
B. Stormscope Antenna
% The Goodrich NY-163 stormscope antenna is located behind the COM #2 antenna (Lycoming
% version) or within the vertical stabilizer (TAE version). The antenna is a combined cross-loop and
sense antenna. The antenna is sealed against environmental extremes. You cannot repair the
antenna.
AIRCRAFT
Navigation
DA 40 Series
AMM
Page 2
20 Sep 2007 34-45-00 Doc # 6.02.01
Rev. 5
C. DA-AV Inverter
% The Mid Continent MD 24-28 (Lycoming version) respective MD 26-14 (TAE version) provides, in
conjunction with the KCS 55A Compass system synchro heading to the WX-500 Stormscope
system.
AIRCRAFT
DA 40 Series
AMM
Navigation
Doc # 6.02.01
Rev. 5 34-45-00 Page 101
20 Sep 2007
Trouble-Shooting
1. General
The table below lists the defects you could have with the Stormscope system. If you have the trouble
detailed in the Trouble column read across to the Possible Cause column. Then do the repair given
in the Repair column.
Trouble Possible Cause Repair
Stormscope does not operate. Circuit-breaker not set.
Faulty cables/connectors.
Set the circuit-breaker.
Do a test for continuity on each
cable. Do a test for short circuit
to ground and between cables.
Replace defective cables.
AIRCRAFT
Navigation
DA 40 Series
AMM
Page 102
20 Sep 2007 34-45-00 Doc # 6.02.01
Rev. 5
Intentionally left blank
AIRCRAFT
DA 40 Series
AMM
Navigation
Doc # 6.02.01
Rev. 5 34-45-00 Page 201
20 Sep 2007
Maintenance Practices
1. General
This Section tells you how to remove/install the components of the Stormscope system. It also tells
you how to test the Stormscope system.
2. Remove/Install the Stormscope Processor
A. Remove the Stromscope Processor
Detail Steps/Work Items Key Items/References
(1) Remove the passengers' seat. Refer to Section 25-10.
(2) Open the 'WX-500'-circuit breaker.
(3) Loosen the screw that attaches the processor to
its mounting tray.
(4) Remove the stormscope processor from the
mounting tray.
B. Install the Stormscope Processor
Detail Steps/Work Items Key Items/References
(1) Put the Stormscope processor in position in the
mounting tray.
(2) Tighten the screw that attaches the processor to
its mounting tray.
(3) Install the passengers' seat. Refer to Section 25-10.
(4) Close the 'WX-500'-circuit breaker.
% (5) Do a test of the Stormscope system. Refer to Paragraph 6.
AIRCRAFT
Navigation
DA 40 Series
AMM
Page 202
20 Sep 2007 34-45-00 Doc # 6.02.01
Rev. 5
% 3. Remove/Install the Stormscope Antenna (Lycoming version)
A. Remove the Stormscope Antenna
Detail Steps/Work Items Key Items/References
(1) Remove the trim/cover from the front face of the
baggage compartment frame.
Pull the rear seat-backs forward.
(2) Open the 'WX-500'-circuit breaker.
(3) Disconnect the connector of the stormscope
antenna.
(4) Remove the screws which attach the stormscope
antenna to the fuselage.
Hold the antenna!
(5) Remove the stormscope antenna from the
fuselage.
B. Install the Stormscope Antenna
Detail Steps/Work Items Key Items/References
(1) Put the stormscope antenna in position on the
fuselage.
(2) Install the screws which attach the stormscope
antenna to the fuselage.
(3) Connect the connector of the stormscope
antenna.
(4) Close the 'WX-500' circuit breaker.
(5) Install the trim/cover to the front face of the
baggage compartment frame.
% (6) Do a test of the stormscope system. Refer to Paragraph 6.
AIRCRAFT
DA 40 Series
AMM
Navigation
Doc # 6.02.01
Rev. 5 34-45-00 Page 203
20 Sep 2007
% 4. Remove/Install the Stormscope Antenna (TAE version)
% A. Remove the Stormscope Antenna
% Detail Steps/Work Items Key Items/References
% (1) Remove the rudder. Refer to Section 55-40 of the AMM.
% (2) Open the 'Wx 500'-circuit breaker.
(3) Disconnect the connector of the Stormscope
% antenna.
%
% (4) Remove the screws which attach the Stormscope
% antenna to the mounting bracket.
Hold the antenna!
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石40系列AMM 2(85)