曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

the landing light.
S Remove the landing light.
B. Install the Landing Light
Detail Steps/Work Items Key Items/References
(1) Hold the taxi light in position in the leading edge of the
left wing.
S Connect the electrical connector to the rear of the
taxi light.
(2) Install the screws which attach the taxi light assembly to
the wing.
(3) Set the ALT/BAT switch (Lycoming version) or
ELECTRIC MASTER key switch (TAE version) to ON.
(4) Set the LANDING circuit -breaker Closed
(5) Set the LANDING switch to ON.
(6) Set the LANDING light switch to OFF.
(7) Set the ALT/BAT switch (Lycoming version) or
ELECTRIC MASTER key switch (TAE version) to OFF.
(8) Install the taxi/landing light cover to the wing:
S Put the light cover in position on the wing.
S Install the 12 screws which attach the light cover to
the wing.
AIRCRAFT
Lights DA 40 Series
AMM
Page 204
20 Sep 2007 33-40-00 Doc # 6.02.01
Rev. 5
4. Replace a Filament in the Wing-Tip Light Unit
A. Replace a Position Light Filament in the Wing-Tip
Detail Steps/Work Items Key Items/References
(1) Set the ALT/BAT switch (Lycoming version) or
ELECTRIC MASTER key switch (TAE version) to OFF.
WARNING: AFTER YOU SET THE POWER TO OFF, MAKE SURE THAT YOU
WAIT A MINIMUM OF FIVE MINUTES BEFORE YOU DO WORK ON
THE STROBE LIGHTS. THE POWER SUPPLIES TO THE STROBE
LIGHTS GENERATE HIGH VOLTAGE. HIGH VOLTAGE CAN CAUSE
DEATH OR INJURY TO PERSONS.
(2) Remove the light unit cover from the wing -tip and the
lamp glasses.
Refer to Figure 1.
(3) Replace the filament.
(4) Install the lamp glass and the light unit cover.
(5) Do an operational test of the position light.
B. Replace a Strobe Light Filament in the Wing-Tip
Detail Steps/Work Items Key Items/References
(1) Set the ALT/BAT switch (Lycoming version) or
ELECTRIC MASTER key switch (TAE version) to OFF.
WARNING: AFTER YOU SET THE POWER TO OFF, MAKE SURE THAT YOU
WAIT A MINIMUM OF FIVE MINUTES BEFORE YOU DO WORK ON
THE STROBE LIGHTS. THE POWER SUPPLIES TO THE STROBE
LIGHTS GENERATE HIGH VOLTAGE. HIGH VOLTAGE CAN CAUSE
DEATH OR INJURY TO PERSONS.
(2) Remove the light unit cover from the wing -tip and the
lamp glasses.
Refer to Figure 1.
(3) Replace the strobe light filament:
% (4) Install the lamp glasses and the light unit cover.
WARNING: DO NOT OPERATE THE STROBE LIGHTS WHEN PERSONS ARE
CLOSE TO THE AIRPLANE AND DO NOT LOOK AT THE LIGHT
WHEN IT OPERATES. STROBE LIGHTS CAN CAUSE EYE DAMAGE.
% (5) Do an operational test of the strobe light.
AIRCRAFT
DA 40 Series
AMM
Lights
Doc # 6.02.01
Rev. 5 33-40-00 Page 205
20 Sep 2007
5. Remove/Install the Light Unit in the Wing-Tip
A. Remove the Light unit in the Wing-Tip
Detail Steps/Work Items Key Items/References
(1) Set the ALT/BAT switch (Lycoming version) or
ELECTRIC MASTER key switch (TAE version) to
OFF and set the LANDING/TAXI/MAP circuitbreakers
open.
WARNING: AFTER YOU SET THE POWER TO OFF, MAKE SURE THAT YOU
WAIT A MINIMUM OF FIVE MINUTES BEFORE YOU DO WORK ON
THE STROBE LIGHTS. THE POWER SUPPLIES TO THE STROBE
LIGHTS GENERATE HIGH VOLTAGE. HIGH VOLTAGE CAN CAUSE
DEATH OR INJURY TO PERSONS.
(2) Remove the light unit cover from the wing -tip and
the lamp glasses.
Refer to Figure 1.
(3) Remove the 3 light filaments.
(4) Remove the light unit from the wing-tip:
S Remove the screws which attach the light unit
to the wing-tip.
S Carefully move the light unit out from the wing
tip.
S Disconnect the 2 connectors from the rear of
the light unit.
S Move the light unit clear from the airplane.
B. Install the Light unit in the Wing-Tip
Detail Steps/Work Items Key Items/References
(1) Put the light unit in position in the wing-tip and
connect the 2 electrical connectors to the rear of
the light unit.
(2) Install the screws that attach the light unit to the
wing-tip.
(3) Install the 3 filaments to the light unit.
AIRCRAFT
Lights DA 40 Series
AMM
Detail Steps/Work Items Key Items/References
Page 206
20 Sep 2007 33-40-00 Doc # 6.02.01
Rev. 5
WARNING: DO NOT OPERATE THE STROBE LIGHTS WHEN PERSONS ARE
CLOSE TO THE AIRPLANE AND DO NOT LOOK AT THE LIGHT
WHEN IT OPERATES. STROBE LIGHTS CAN CAUSE EYE DAMAGE.
(4) Do an operational test of the position and strobe
lights:
S Set the ALT/BAT switch (Lycoming version)
or ELECTRIC MASTER key switch (TAE
version) to ON.
S Set the LANDING, TAXI/MAP and STROBE
circuit-breakers closed.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石40系列AMM 2(67)