曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

spring washers are between the top of
% the strut and the mounting block. Make
% sure that the convex and concave
% washers are between the nut and the
% strut.
(9) Tighten the nut on the inner bolt and install a
cotter pin.
To give a height of the spring washers of
4 mm (+0.5 mm / -0 mm) or
0.16 in. (+0.02 in / -0 in).
AIRCRAFT
Landing Gear
DA 40 Series
AMM
Detail Steps/Work Items Key Items/References
Page 204
20 Sep 2007 32-10-00 Doc # 6.02.01
Rev. 5
(10) Connect the bonding cable to the strut. Install the nut and bolt near the inner
mounting block.
(11) Install the axle, brake torque-plate and the
mounting plate for the wheel fairing. Install the 6
bolts which attach the axle.
Refer to Figure 2. Torque: 6.4 Nm (4.7
ft.lb).
(12) Install the brake caliper. Refer to Section 32-40.
(13) Install the wheel. Refer to Section 32-40.
(14) Install the back-plate to the brake caliper. Refer to Section 32-40.
(15) Install the wheel fairing:
S Install the outer bolt.
S Install 4 screws on the inner side.
(16) Install the strut fairing:
S Install strut fairing.
S Install stub wing cover.
S Install brake cover.
Optional, see OÄM 40-106.
Take care of padding on strut.
Take care of padding on strut cover.
(17) Lower the airplane with jacks. Refer to Section 07-10.
(18) Do a test for correct adjustment of the landing
gear.
See Paragraph 3.
(19) Do a function test of the wheel brake system.
AIRCRAFT
DA 40 Series
AMM
Landing Gear
Doc # 6.02.01
Rev. 5 32-10-00 Page 205
20 Sep 2007
3. Test/Adjust the Main Landing Gear
Do this work at the following times:
) When required by the maintenance checklist (Chapter 05).
) After a hard landing.
) After any repair to the main landing gear strut.
A. Equipment
Item Quantity Part Number
Slide sheets - 2 per side. 4 Commercial.
AIRCRAFT
Landing Gear
DA 40 Series
AMM
Page 206
20 Sep 2007 32-10-00 Doc # 6.02.01
Rev. 5
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
Figure 3: Measure Toe-In and Camber
AIRCRAFT
DA 40 Series
AMM
Landing Gear
Doc # 6.02.01
Rev. 5 32-10-00 Page 207
20 Sep 2007
B. Procedure
Detail Steps/Work Items Key Items/References
(1) Make sure that the airplane is at the empty
weight.
See the Adjustment Report for the
airplane.
(2) Remove the strut fairings, if installed:
S Remove brake cover.
S Remove stub wing cover.
S Remove strut fairing.
Optional, see OÄM 40-106.
Remove bolts and washers.
Remove bolts and washers.
Remove bolts and washers at the rear.
(3) Remove the wheel fairings:
S Remove the outer bolt.
S Remove 4 screws from the inner side.
For each wheel.
(4) Move the airplane to put the main wheels on the
slide sheets.
(5) Measure the toe-in. Refer to Figure 3.
(6) Measure the camber. Refer to Figure 3.
WARNING: USE ONLY THE SHIMS LISTED FOR THE PURPOSE IN THE
ILLUSTRATED PARTS CATALOGUE. OTHER SHIMS COULD CAUSE
LANDING GEAR FAILURE.
(7) If necessary, adjust the toe-in and/or camber. Refer to Chapter 06-00 for limits.
Maximum 2° shim per side (camber +
toe). See the Illustrated Parts
Catalogue for the correct shims.
Put shims between the strut and the
axle.
These change the angle between the
axle and the airplane longitudinal or
vertical axis.
(8) Measure the wheel track. Across the airplane from the outermost
point on one axle to the outermost point
on the other axle.
(9) Move the airplane off the slide sheets.
AIRCRAFT
Landing Gear
DA 40 Series
AMM
Detail Steps/Work Items Key Items/References
Page 208
20 Sep 2007 32-10-00 Doc # 6.02.01
Rev. 5
(10) Install the wheel fairings:
S Install the outer bolt.
S Install 4 screws on the inner side.
(11) Install the strut fairings:
S Install strut fairing.
S Install stub wing cover.
S Install brake cover.
Optional, see OÄM 40-106.
Take care of padding on strut.
Take care of padding on strut cover.
AIRCRAFT
DA 40 Series
AMM
Landing Gear
Doc # 6.02.01
Rev. 5 32-20-00 Page 1
20 Sep 2007
Section 32-20
Nose Landing Gear
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石40系列AMM 2(54)