曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Vp-p.
(d) When you complete the output level adjustment, push the F6 key.
You will hear a "click".
(e) Make sure that the term "BITE OFF" is shown for channel 02.
Page 142.05
Feb 20/2002
Matsushita Avionics Systems Corporation
COMPONENT MAINTENANCE MANUAL
PART NUMBER RD-AA5002 SERIES
23-32-47
(9) Second Type A8 Card
Refer to Figure 103M for the location of the variable resistor
A8VR501.
VR501
A8 CARD CN503
BOTTOM
TOP
FRONT REAR
LOCATION OF VARIABLE RESISTOR ON A8 CARD
Figure 103M
Do the output level adjustment as follows:
(a) Set the VMU tuner for reception of CH2 and make sure that the
oscilloscope shows a video signal waveform as shown in Figure
103N.
(b) Turn A8VR501 and adjust the amplitude of the video signal shown
on the oscilloscope to 0.8 Vp-p.
0.8 Vp-p
A8VR501 ADJUSTS
THIS AMPLITUDE.
ADJUSTMENT OF OUTPUT LEVEL OF INTERNAL VIDEO SIGNAL GENERATOR
Figure 103N
(c) When you complete the output level adjustment, push the F6 key.
You will hear a "click".
(d) Make sure that the term "BITE OFF" is shown for channel 02.
Page 142.06
Feb 20/2002
Matsushita Avionics Systems Corporation
COMPONENT MAINTENANCE MANUAL
PART NUMBER RD-AA5002 SERIES
23-32-47
THIS PAGE IS
INTENTIONALLY
LEFT BLANK.
Page 143
Jul 20/2005
Panasonic Avionics Corporation
COMPONENT MAINTENANCE MANUAL
PART NUMBER RD-AA5002 SERIES
23-32-47
8. Wiring and Schematic Diagrams
A. The wiring and schematic diagrams are given as shown in the table below.
The EFFECTIVITY column shows the part numbers to which the diagram
applies. MOD numbers, serial numbers and/or other identification are
also shown as necessary to identify the applicability of the diagrams.
FIG FIGURE TITLE EFFECTIVITY
104 Wiring diagram of video modulator unit RD-AA5002-12,
RD-AA5002-22
104A Wiring diagram of video modulator unit RD-AA5002-23
104B Wiring diagram of video modulator unit RD-AA5002-25
105 Schematic diagram of CPU card assembly (A1) All part numbers
106 Schematic diagram of modulator card
assembly (A2)
Without MOD10 for
RD-AA5002-12,
Without MOD12 for
RD-AA5002-22/-23.
106A Schematic diagram of modulator card
assembly (A2)
MOD10 for RD-AA5002-12,
MOD12 for RD-AA5002-22/-23,
All units for RD-AA5002-25.
107 Schematic diagram of RF power card assembly
(A3)
Without MOD14 for
RD-AA5002-12,
Without MOD16 for
RD-AA5002-22/-23,
Without MOD4 for
RDAA5002-25.
107A Schematic diagram of RF power card assembly
(A3)
MOD14 for RD-AA5002-12,
MOD16 for RD-AA5002-22/-23,
MOD4 for RD-AA5002-25.
108 Schematic diagram of power card assembly
(A4)
All part numbers
109 Schematic diagram of mother card assembly
(A5)
Card P/N R8U5AA5002ZA for
all part numbers
109A Schematic diagram of mother card assembly
(A5)
Card P/N R8U5AA5002ZB and
after for all part numbers
110 Schematic diagram of video signal generator
card assembly (A8)
Without MOD7 for
RD-AA5002-12,
Without MOD9 for
RD-AA5002-22/-23.
110A Schematic diagram of video signal generator
card assembly (A8)
MOD7 for RD-AA5002-12,
MOD9 for RD-AA5002-22/-23,
All units for
RD-AA5002-25.
Page 144
Jul 20/2005
Panasonic Avionics Corporation
COMPONENT MAINTENANCE MANUAL
PART NUMBER RD-AA5002 SERIES
23-32-47
NOTE: The schematic diagrams of the A6 and A7 cards are included in the
wiring diagram (Figures 104 thru 104B).
B. Revision Reference Sheet
A revision reference sheet is included in front of each wiring or
schematic diagram. This sheet contains a descriptive history of changes
made to the equipment that have an effect on the wiring or schematic
diagram.
The EFFECTIVITY column of the sheet identifies when the change became
effective with the part numbers, MOD numbers, serial numbers and/or other
identification. If a part number contains the change from its first
production unit, the EFFECTIVITY column shows no data for that part
number.
C. Notes on Graphic Symbols
(1) Ground Symbols
We use different symbols for the signal ground, analog ground and
chassis ground as follows:
SIGNAL GROUND ANALOG GROUND CHASSIS GROUND
The analog ground symbol shows only on Figure 110A (A8 card). The
analog ground and signal ground are connected together on the A8
card. The signal ground also connects to the chassis ground through
the A3 card and J1 connector.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：COMPONENT MAINTENANCE MANUAL Video Modulator Unit (VMU)(44)