曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

T&FI-2
Page 164
Feb 20/2002
Matsushita Avionics Systems Corporation
COMPONENT MAINTENANCE MANUAL
PART NUMBER RD-AA5002 SERIES
23-32-47
G. Fault Isolation Procedure for Microcontroller (A1IC102)
NEXT STEP IF
STEP CHECK/POSSIBLE FAULT
YES NO
G-1 Is a clock signal (approximately 4 MHz) applied to
A1IC102 pin 40 or 41? G-3 G-2
G-2 If +5V is applied to pins 34, 35, 36, 39 and 42 of
A1IC102, A1X101 is possibly defective.
--- ---
G-3 Is H applied to A1IC102 pin 1 (reset)? G-5 G-4
G-4 Replace A1IC101. --- ---
G-5 Is H applied to A1IC102 pins 2 and 33? G-7 G-6
G-6 Replace A1IC113. --- ---
G-7 If A1IC102 does not operate correctly, replace it. --- ---
T&FI-2
Page 165
Feb 20/2002
Matsushita Avionics Systems Corporation
COMPONENT MAINTENANCE MANUAL
PART NUMBER RD-AA5002 SERIES
23-32-47
H. Fault Isolation Procedure for A2 Card Failure
For easy identification of the problem, we use an example in the
procedure that the modulator status is "FAIL" for CH5.
NEXT STEP IF
STEP CHECK/POSSIBLE FAULT
YES NO
H-1 If the modulator status is "FAIL" for CH5, replace the
CH5 A2 card with one of the other A2 cards.
Is the status "FAIL" for the same channel?
H-9 H-2
H-2 Put the A2 cards back to their initial positions. A
fault is on the CH5 A2 card.
Is there a clock signal at pin 4 of A2IC204? H-4 H-3
H-3 Examine the CK input circuit (A2Q202) to find a fault. --- ---
H-4 Is there a data signal at pin 3 of A2IC204? H-6 H-5
H-5 Examine the DT input circuit (A2Q202) to find a fault. --- ---
H-6 Is A2IC204 pin 20 output L? H-7 H-8
H-7 Examine the LD output line for an open-circuit fault. --- ---
H-8 Examine the PLL frequency synthesizer circuit to find a
fault. --- ---
H-9 There is an open- or short-circuit fault of the DT05,
CK05 or LD05 line on the A5 or A1 card. --- ---
T&FI-2
Page 166
Feb 20/2002
Matsushita Avionics Systems Corporation
COMPONENT MAINTENANCE MANUAL
PART NUMBER RD-AA5002 SERIES
23-32-47
I. Fault Isolation Procedure for A1 Card
NEXT STEP IF
STEP CHECK/POSSIBLE FAULT
YES NO
I-1 Is the modulator status "FAIL" for CH1, CH2, CH5, CH6,
CH9 and CH10? I-2 I-3
I-2 A1IC105 is possibly defective. --- ---
I-3 Is the modulator status "FAIL" for CH3, CH4, CH7, CH8,
CH11 and CH12? I-4 I-5
I-4 A1IC106 is possibly defective. --- ---
I-5 Is the modulator status "FAIL" for CH1, CH2, CH3, CH4,
CH5, CH6 and CH7? I-6 I-7
I-6 A1IC107 or A1IC109 is possibly defective. --- ---
I-7 Is the modulator status "FAIL" for CH8, CH9, CH10, CH11
and CH12? I-8 I-9
I-8 A1IC108 or A1IC110 is possibly defective. --- ---
I-9 There is possibly a short-circuit between two CK or LD
lines on the A1 or A5 card. --- ---
T&FI-2
Page 167
Feb 20/2002
Matsushita Avionics Systems Corporation
COMPONENT MAINTENANCE MANUAL
PART NUMBER RD-AA5002 SERIES
23-32-47
6. Adjustments
Do the adjustment procedures given below as necessary and as continued from
the functional testing. You can do each adjustment procedure independently.
A. Disassembly Necessary for Adjustments
(1) Do not set the tester's POWER switch to OFF if you adjust the RF
levels.
(2) Disassemble as follows:
ADJUSTMENT DISASSEMBLY
RF levels and/or
modulation depth
Remove the top cover assembly [1-10].
Output level of internal
video signal generator
Put the UUT with its top down, then remove the
bottom cover [1-35].
B. RF Levels
If it is necessary to adjust the RF level of a modulator channel, we
recommend that you adjust the RF levels of all modulator channels as
given below.
(1) Use the same setup as the functional test setup (Figure 111).
(2) RF Output Connections
(a) Connect the RF OUTPUT RF1 connector of the tester to the input
of the spectrum analyzer with an RF cable (RFC1).
(b) Connect BNC 50-W terminators to the RF OUTPUT RF2, RF3 and RF4
connectors of the tester.
(3) Disconnect the BNC tee adapter T1 from the tester (no modulation).
(4) Start the adjustment mode (ref. 5.B.).
(5) The user configuration is initially shown. If the frequencies are
not in the range from 151.25 to 283.25 MHz at intervals of 12 MHz,
click on the "FACTORY SETTING" button to set this frequency range.
(6) Make sure that the UUT is energized for more than 2 hours.
T&FI-2
Page 168
Feb 20/2002
Matsushita Avionics Systems Corporation
COMPONENT MAINTENANCE MANUAL
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：COMPONENT MAINTENANCE MANUAL Video Modulator Unit (VMU)(78)