曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

(2) Connectors and Connections
We use the symbols given below for the stationary connectors, plug
connectors and soldered connections:
1
2
3
4
STATIONARY
CONNECTOR
PLUG
CONNECTOR
1
2
3
4
SOLDERED
CONNECTIONS
Page 145
Jul 20/2005
Panasonic Avionics Corporation
COMPONENT MAINTENANCE MANUAL
PART NUMBER RD-AA5002 SERIES
23-32-47
(3) Power Lines
The power line symbols are as follows:
+5V +5VB
D. Equipment Designators
The electronic and electrical parts on the printed circuit card
assemblies have a card designator as a prefix to their equipment
designator, but such is not shown on the schematic diagrams.
E. Symbol for Safety-requested Parts
The safety-requested parts are major parts in high voltage circuits or
power lines, and are identified by mark “ “ near part symbols.
F. Values
(1) All resistance values shown on the schematic diagrams are in ohms,
with K for kilo-ohms and M for meg-ohms.
(2) All capacitance values shown on the schematic diagrams are in
microfarads, with P for picofarads and F for farads.
(3) All inductance values shown on the schematic diagrams are in
microhenries (uH) or turns (T).
G. Electrostatic Sensitive Devices
Electrostatic discharges from your hands or tools can cause permanent
damage to most of the semiconductor devices on the printed circuit card
assemblies. Obey the general precautions given below to prevent such
damages:
· Do the disassembly and assembly work on a grounded conductive surface.
· Put on a conductive wrist-strap that is grounded.
· Touch your tool to the ground (grounded metal structure, etc.) before
you use it.
· Use a tip-grounded soldering iron.
· Put the removed printed circuit card assembly on a grounded conductive
surface.
Page 146
Feb 20/2002
Panasonic Avionics Corporation
COMPONENT MAINTENANCE MANUAL
PART NUMBER RD-AA5002 SERIES
23-32-47
THIS PAGE IS
INTENTIONALLY
LEFT BLANK.
Page 147
Feb 20/2002
Matsushita Avionics Systems Corporation
COMPONENT MAINTENANCE MANUAL
PART NUMBER RD-AA5002 SERIES
23-32-47
REVISION
CODE
REVISION DESCRIPTION EFFECTIVITY
1 Changed A6F1 from fast-acting 8 A to time-delay
3.15 A and A6F2 from fast-acting 2 A to timedelay
800 mA for correct short-circuit
protection.
MOD9 for
RD-AA5002-12,
MOD11 for
RD-AA5002-22
Revision Reference Sheet For Figure 104
Page 148
Feb 20/2002
Matsushita Avionics Systems Corporation
COMPONENT MAINTENANCE MANUAL
PART NUMBER RD-AA5002 SERIES
23-32-47
THIS PAGE IS
INTENTIONALLY
LEFT BLANK.
Page 149/150
Feb 20/2002
Matsushita Avionics Systems Corporation
COMPONENT MAINTENANCE MANUAL
PART NUMBER RD-AA5002 SERIES
23-32-47
WIRING DIAGRAM OF VIDEO MODULATOR UNIT
Figure 104
CN402 12
FAN
ASSEMBLY 12
CN5 A1 CN401
THRU
A1
THRU
A4
A13
THRU
A13
THRU
CN201 CN7
A4
THIS DIAGRAM APPLIES TO P/N RD-AA5002-12 AND RD-AA5002-22.
MODULATOR
CARD
ASSEMBLY
(A2)
B4
B13
C4
C13
SC1
THRU
THRU
B13
C13
SC1
THRU
THRU
CN201 CN8
B4
C4
MOTHER
CARD
ASSEMBLY
A32
B1
B32
CN40 1 1
THRU
A32
B1
B32
THRU
1 1 CN501
POWER CARD
ASSEMBLY
(A4)
CN503 123
CN502
3
5
2345 123456
VIDEO SIGNAL
GENERATOR
CARD ASSEMBLY
(A8)
FUSE CARD
123456
T1
7.5V
CN39
2345
3
5
1234
1234
(A5)
THERE ARE 12 MODULATOR CARD
SLOTS ON MOTHER CARD ASSEMBLY.
THEY ARE A5CN7 THRU A5CN18.
NOTE:
A4
A13
B4
B13
C4
C13
SC1
THRU
THRU
THRU
A13
B13
C13
SC1
THRU
THRU
THRU
A4
B4
C4
CN9
CN10
CN11
MODULATOR
CARD
ASSEMBLY
(A2)
MODULATOR
A4
A13
B4
THRU
A13
THRU
CN201 A4 CN18
B4
CN12
CN13
CN14
CN15
CN16
CN17
CN22
CN21
12
12
12345
12345
CN3
123
123
1
12345
CN2
ASSEMBLY (A6)
CN4
T2
8V X 2
27V
F1
3.15A
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：COMPONENT MAINTENANCE MANUAL Video Modulator Unit (VMU)(45)