曝光臺(tái) 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費(fèi)者

Monitor (C/A)
This unit receives the composite color video signal
from the VMU tuner and shows color pictures. The
input impedance must be 75 W (±1%).
NOTE: If you use your RF video receiving equipment
for VMU testing (Toshiba TT-GC9 or TT-GC10 TV
tuner, video cassette recorder, etc.), the
monitor must be the one that is connected to
your receiving equipment.
T&FI-2
Oscilloscope (C/A) DC to 40 MHz, precision of ±3% for 1 Vp-p video
signal measurements.
T&FI-2
RF Cable (C/A) BNC-BNC 50-W coaxial cable. Three sets are
necessary (RFC1 thru RFC3).
T&FI-2
Video Cable (C/A) BNC-BNC coaxial cable. Four sets are necessary
(VC1 thru VC4). The cable impedance can be 50 or
75 W.
T&FI-2
BNC Tee Adapter
(C/A)
Two sets are necessary (T1 and T2). T&FI-2
Monitor Cable (C/A) One set is necessary to connect the output (BNC) of
the VMU tuner to the input of the video monitor.
T&FI-2
CPU Extension Card,
RD-AM9357-1
(Panasonic)
It connects to the A5 card and gives an extended
connection for the A1 card for fault isolation.
T&FI-2
Page 907
Nov 20/2006
Panasonic Avionics Corporation
COMPONENT MAINTENANCE MANUAL
PART NUMBER RD-AA5002 SERIES
23-32-47
(Cont'd)
ITEM (SOURCE) DESCRIPTION EFF
Modulator Extension
Card,
RD-AM9357-2
(Panasonic)
It connects to the A5 card and gives an extended
connection for the A2 card for fault isolation.
T&FI-2
Power Extension
Card, RD-AM9357-3
(Panasonic)
It connects to the A5 card and gives an extended
connection for the A4 card for fault isolation.
T&FI-2
Ceramic Alignment
Screwdriver or
Flat-Blade
Screwdriver (C/A)
Use this to turn VR100, VR101, VR200 and VR201
(variable resistors) on the A1 card and VR301 on A4
card. We recommend to use a ceramic alignment
screwdriver (all insulating material) to prevent
accidental damage to the A1 and A4 cards.
T&FI-2
Volt-Ohm-
Milliammeter (VOM)
or Digital
Multimeter (DMM)
(C/A)
Use a VOM or DMM for continuity check and fault
isolation. It must be an "ISOLATED" type, such as
a battery-operated one, for fault isolation on the
primary circuits of the A5 card.
T&FI-2
Standard Tools
(C/A)
Use them as necessary. ---
Ethyl Alcohol or
Isopropyl Alcohol
(C/A)
Use this to clean the printed circuit card
assemblies.
---
Neutral Detergent
(C/A)
Use this to clean the external surfaces of the
covers and plates.
---
Soft Bristle Brush
(C/A)
Use this to remove dust and dirt from printed
circuit card assemblies.
---
Toothbrush (C/A) Use this with alcohol to clean the dirty areas on
the printed circuit card assemblies.
---
Clean Low-Lint
Cloth (C/A)
Use this to clean or dry the surfaces. ---
Cotton Swab (C/A) Use this to clean small parts and recesses. ---
Compressed air (air
jet) (C/A)
An air source and a nozzle with a manual control.
The nozzle gives an air jet at a pressure of 0.2
MPa (28 psig) maximum. The air jet must be clean
and dry.
---
Purified Water
(C/A)
Use this to clean the printed circuit card
assemblies.
---
Power Desoldering
Station (C/A)
Type suitable for multilayer applications with
vacuum pump suction, grounded tip.
---
Page 908
Jul 20/2005
Panasonic Avionics Corporation
COMPONENT MAINTENANCE MANUAL
PART NUMBER RD-AA5002 SERIES
23-32-47
(Cont'd)
ITEM (SOURCE) DESCRIPTION EFF
Soldering Iron for
Tin-Lead Solder
(C/A)
Type and size good for repair of electronic
equipment, grounded tip.
---
Soldering Iron for
Lead-Free Solder
(C/A)
Type and size good for repair of electronic
equipment, grounded tip. Higher temperatures are
necessary for soldering with lead-free solder.
---
Contact Removal
Tool for Straight
Coax Contacts (C/A)
Use this to remove the coax contacts from the A5CN6
thru A5CN18 connectors on the A5 card. You can get
this tool from:
• Siemens.
P/N C42407-A67-A1 (70-mm long) or C42407-A67-A2
(200-mm long).
• Hirose Electric Co., Ltd., Tokyo, Japan.
P/N PO51P-T-1 (CL350-0037-1).
---
Contact Removal
Tool for Right-
Angle Coax Contacts
(C/A)
Use this to remove the coax contacts from the
A2CN201 connector on each A2 card. You can get
this tool from:
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：COMPONENT MAINTENANCE MANUAL Video Modulator Unit (VMU)(92)