(2)
Clean the foam plastic (polyurethane) parts (Ref. TASK 25-13-00-100-001).
(3)
Clean the overhead panel, the glareshild, the main instrument panel, the lateral consoles and the center pedestal.
(a)
Put a CAP - PROTECTION on each electrical outlet.
(b)
Remove the loose dirt from the surface with a BRUSH - BRISTLED,
R Linings and Furnishings - Cockpit Figure 304/TASK 12-21-12-991-007
1EFF : 1 1 1CES ALL 1 111 12-21-12 Page 317 Aug 01/05
FIBER, SOFT and a vacuum cleaner. R (Ref. Fig. 305/TASK 12-21-12-991-001)
CAUTION : USE ONLY THE SPECIFIED MATERIALS AND OBEY THE
_______ INSTRUCTIONS FROM THE MANUFACTURERS. OTHER MATERIALS CAN CAUSE DAMAGE TO THE SURFACE PROTECTION OF THE COMPONENTS AND THE RELATED AREA.
(c) Moisten a clean lint-free cotton cloth MISCELLANEOUS (Material No. 19-003) with CLEANING AGENTS (Material No. 11-017) and apply it to the surface you will clean.
R NOTE : To prevent contamination of the cleaning agent, do not put
____ R the cloth into the cleaning agent.
(d) Moisten a clean lint-free cotton cloth MISCELLANEOUS (Material No. 19-003) with warm clean water and lightly rub the surface you will clean.
NOTE : Always make the cloth moist, not the part you will clean.
____
(e) Dry the surface with a clean lint-free cotton cloth MISCELLANEOUS (Material No. 19-003).
(4)
Clean the Seats
(a) Clean the seats as given in the (Ref. CMM 25-11-XX) of the seat manufacturer.
(5)
Clean the floor
(a)
Remove the loose dirt with a vacuum cleaner. NOTE : The following work steps are only applicable if
(b)
Apply CLEANING AGENTS (Material No. 11-017) to the surface with a BRUSH - BRISTLED, FIBER, STIFF.
____ non-textile floor covering (NTF) is installed.
R Vacuum Cleaner Sockets Figure 305/TASK 12-21-12-991-001
1EFF : 1 1 1CES ALL 1 111 12-21-12 Page 319 Aug 01/05
R NOTE : To prevent contamination of the cleaning agent, do not put
____ R the brush into the cleaning agent.
(c)
Clean the surface with a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003) and warm clean water.
(d)
Dry the surface with a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003).
(6)
Remove the protection caps from the electrical outlets.
(7)
Make sure that the work area is clean and clear of tool(s) and other items.
5. Close-up
________
Subtask 12-21-12-862-055
A. De-energize the ground service network
(Ref. TASK 24-42-00-862-001).
TASK 12-21-12-100-003
R Cleaning of the Carpets and Non-Textile Floor Covering (NTF)
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific vacuum cleaner
No specific 1 BRUSH - BRISTLED, FIBER, MEDIUM
No specific 1 BRUSH - BRISTLED, FIBER, STIFF
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
No specific warm clean water
No specific warm water
Material No. 11-017 USA AMS 1550
INTERIOR GENERAL PLASTIC CLEANER (Ref. 20-31-00) Material No. 11-018 USA AMS 1630 CARPET AND FABRIC CLEANER (Ref. 20-31-00) Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power 24-42-00-862-001 De-energize the Ground Service Network Supplied from
the External Power R 12-21-12-991-001 Fig. 305 R 12-21-12-991-005 Fig. 306
3. Job Set-up
__________
Subtask 12-21-12-861-056
A. Energize the ground service network
(Ref. TASK 24-42-00-861-001).
4. Procedure 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM SERVICING 1(127)
