1EFF : 001-049, 051-061, 101-105, 201-203, 1 12-13-27Page 329 1 1 Aug 01/05R 1 1 1CES 1
(i)
Disconnect the supply hose from the drain plug adaptor.
(j)
Disconnect the waste hose from the vent plug adaptor.
(k)
Connect the waste hose to the drain plug adaptor.
(l)
Use the empty oil gun (A663130/4) to pressurize the applicable flap actuator with air, as follows:
1 Connect the oil gun hose to the vent plug adaptor, slowly
_
pressurize the applicable flap actuator.
2 Continue to supply air, until air only is released from the
_
waste hose. Stop the air supply.
3 Remove the oil gun hose and the vent plug adaptor.
_
4 Remove the waste hose and the drain plug adaptor.
_
5 Clean the applicable component interfaces and the adjacent
_
area with a MISCELLANEOUS (Material No. 19-003) made moist
with CLEANING AGENTS (Material No. 11-004).
6 Make sure that the parts retained from the removed component
_
are clean and in the correct condition.
7 Do an inspection of the component interface and/or the
_
adjacent area.
8 Apply SPECIAL MATERIALS (Material No. 05-002) to the vent plug
_
(3), and the drain plug (4).
9 Install the vent plug (3), and the drain plug (4).
_ 10 Torque the vent plug (3) to between 0.54 and 0.66 m.daN (47.78
__ and 58.40 lbf.in).
11 Torque the drain plug (4) to between 0.54 and 0.66 m.daN
__ (47.78 and 58.40 lbf.in).
1EFF : 001-049, 051-061, 101-105, 201-203, 1 12-13-27Page 330 1 1 Aug 01/05R 1 1 1CES 1
Subtask 12-13-27-612-058
C. Replenishment of the offset gearboxes of the No.3 flap actuators (6221CM,6271CM) (Ref. Fig. 304/TASK 12-13-27-991-004)
(1)
Use a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-004) to clean the area around the vent plug (5), and the drain plug (6).
(2)
Remove the vent plug (5), and the drain plug (6).
(3)
Use the FILLING KIT-ACTUATOR (A663160) to fill the applicable flap actuator, as follows:
(a)
Install the vent plug adaptor 3/8 UNF (A663159/1) to the vent plug hole of the applicable flap actuator.
(b)
Install the drain plug adaptor 5/16 UNF (A663159/2) to the drain plug hole of the applicable flap actuator.
(c)
Assemble the semi-fluid pump (A663130/3) to the semi-fluid container (A663130/7).
(d)
Connect the supply hose from the semi-fluid pump to the drain plug adaptor.
(e)
Assemble the waste lid (A663130/5) to the used fluid container (A663130/6).
(f)
Connect the waste hose from the waste lid to the vent plug adaptor.
(g)
Use the semi-fluid pump to slowly fill the applicable flap actuator.
(h)
Continue to fill the applicable flap actuator until clean COMMON GREASE (Material No. 04-025) flows from the waste hose.
(i)
Disconnect the supply hose from the drain plug adaptor.
(j)
Disconnect the waste hose from the vent plug adaptor.
(k)
Connect the waste hose to the drain plug adaptor.
1EFF : 001-049, 051-061, 101-105, 201-203, 1 12-13-27Page 331 1 1 Aug 01/05R 1 1 1CES 1
(l) Use the empty oil gun (A663130/4) to pressurize the applicable flap actuator with air, as follows:
1_ Connect the oil gun hose to the vent plug adaptor, slowly
pressurize the applicable flap actuator.
2_ Continue to supply air, until air only is released from the
waste hose. Stop the air supply.
3_ Remove the oil gun hose and the vent plug adaptor.
4_ Remove the waste hose and the drain plug adaptor.
5_ Clean the applicable component interfaces and the adjacent
area with a MISCELLANEOUS (Material No. 19-003) made moist
with CLEANING AGENTS (Material No. 11-004).
6_ Make sure that the parts retained from the removed component
are clean and in the correct condition.
7_ Do an inspection of the component interface and/or the
adjacent area.
8_ Apply SPECIAL MATERIALS (Material No. 05-002) to the vent plug
(5), and the drain plug (6).
9_ Install the vent plug (5), and the drain plug (6).
10__ Torque the vent plug (5) to between 0.54 and 0.66 m.daN (47.78
and 58.40 lbf.in).
11__ Torque the drain plug (6) to between 0.36 and 0.44 m.daN
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM SERVICING 1(74)
