(2) Make sure that the ECAM DU shows the intercell transfer valves in the open position.
Subtask 12-11-28-865-052
F. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FUEL/XFR VALVE1/WING/R 2QP A11 49VU FUEL/XFR VALVE1/WING/L 1QP A10 121VU FUEL/XFR VALVE2/WING/R 4QP M23 121VU FUEL/XFR VALVE2/WING/L 3QP M22
**ON A/C ALL
4. Procedure
_________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 12-11-28-650-060
A. Overwing (Gravity) Refuel
(1)
Connect the ground-cable of the refuel nozzle to the wing ground-connection.
(2)
Remove the applicable overwing refuel cap 44QM(45QM).
(3)
Put the fuel nozzle in the overwing refuel point. CAUTION : KEEP THE RATE OF REFUEL THE SAME AS, OR LESS THAN, THE RATE
_______ OF FLOW THROUGH THE TRANSFER VALVES.
(4)
Start the pump on the fuel tanker/pump unit.
(5)
Use the fuel pumps in the wing tanks to move the fuel to the center tank from the wing tanks (Ref. TASK 28-25-00-869-001).
(6)
Continually monitor the fuel quantities on the ECAM lower DU. NOTE : The overwing refuel point is not at the highest point on the
____ wing. Thus you cannot refuel the wing tanks to full.
(7)
When the fuel quantities are correct, stop the pump on the fuel tanker/pump unit.
(8)
Remove the fuel nozzle from the overwing refuel point.
(9)
Install the overwing refuel cap 44QM(45QM).
(10)
Disconnect the ground-cable of the refuel nozzle from the wing ground-connection.
(11)
Do the refuel procedure again for the other wing.
(12)
Correct the fuel configuration (move the fuel from the inner cells of the wing tanks to fill the outer cells of the wing tanks (Ref. TASK 28-25-00-869-001)).
**ON A/C 301-399,
Subtask 12-11-28-650-060-A
A. Overwing (Gravity) Refuel
(1)
Connect the ground-cable of the refuel nozzle to the wing ground-connection.
(2)
Remove the applicable overwing refuel cap 44QM(45QM).
(3)
Put the fuel nozzle in the overwing refuel point.
(4)
Start the pump on the fuel tanker/pump unit.
(5)
Continually monitor the fuel quantities on the ECAM lower DU. NOTE : The overwing refuel point is not at the highest point on the
____ wing. Thus you cannot refuel the wing tanks to full.
(6)
When the fuel quantities are correct, stop the pump on the fuel tanker/pump unit.
(7)
Remove the fuel nozzle from the overwing refuel point.
(8)
Install the overwing refuel cap 44QM(45QM).
(9)
Disconnect the ground-cable of the refuel nozzle from the wing ground- connection.
(10) Do the refuel procedure again for the other wing.
R 1EFF : ALL 1 12-11-28Page 353 1 1 May 01/05 1 1 1CES 1 **ON A/C ALL
5. Close-up
________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 12-11-28-860-062
A. Aircraft Configuration
(1)
Disconnect these bonding/ground cables:
-between the aircraft and the fuel tanker/pump unit
-
if applicable, between the fuel tanker/pump unit and the ground
-
if applicable, between the aircraft and the ground.
(2)
To close the intercell transfer valves:
(a)
On the refuel/defuel control panel 800VU put the MODE SELECT switch to REFUEL.
(b)
Make sure that the ECAM DU shows the intercell transfer valves closed (cross-line).
(c)
On the refuel/defuel control panel 800VU, put the MODE SELECT switch to OFF.
Subtask 12-11-28-410-057
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the access door 192MB.
**ON A/C 301-399,
Subtask 12-11-28-860-062-A
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM SERVICING 1(33)
