Flap Actuator - Track 1
Figure 305/TASK 12-13-27-991-005
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 12-13-27Page 343 1401-499, 1Aug 01/05 1 1 1CES 1
Flap Actuator - Track 1
Figure 305A/TASK 12-13-27-991-005-A
R 1EFF : 301-399, 1 12-13-27 Page 344
1 1 Aug 01/05
1 1
1CES 1
INTENTIONALLY BLANK
R 1 1
12-13-27Page 345
1 1 Aug 01/05 1 1 1CES 1
Flap Actuators - Tracks 2 thru 4 Figure 306/TASK 12-13-27-991-006- 13 (SHEET 1)
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 12-13-27Page 346 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
Flap Actuators - Tracks 2 thru 4 Figure 306/TASK 12-13-27-991-006- 23 (SHEET 2)
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 12-13-27Page 347 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
Flap Actuators - Tracks 2 thru 4 Figure 306/TASK 12-13-27-991-006- 33 (SHEET 3)
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 12-13-27Page 348 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(d)
Connect the FILLING KIT-ACTUATOR (A663160) to fill the flap actuator, as follows:
(e)
Operate the semi-fluid pump and slowly fill the flap actuator with clean COMMON GREASE (Material No. 04-025). Operate the pump handle through its full travel until clean semi-fluid flows from the drain hose.
(f)
Disconnect the supply hose from the vent plug adaptor.
(g)
Remove the vent plug adaptor from the flap actuator.
(h)
Disconnect the waste hose from the drain plug adaptor.
(i)
Remove the drain plug adaptor from the flap actuator. NOTE : The vent plug (1) and the drain plug (2) are torque
____ tightened at the end of this procedure.
(j)
Install (but do not torque tighten) the vent plug (1) in the flap actuator.
(k)
Install (but do not torque tighten) the drain plug (2) in the flap actuator.
1_ Install the vent plug adaptor 3/8 UNF (A663159) in the vent
plug hole of the flap actuator.
2_ Install the drain plug adaptor 3/8 UNF (A663159) in the drain
plug hole of the flap actuator.
3_ Assemble the semi-fluid pump (A663130/3) to the semi-fluid
container (A663130/7).
4_ Connect the supply hose from the semi-fluid pump to the vent
plug adaptor.
5_ Assemble the waste lid (A663130/5) to the used fluid container
(A663130/6).
6_ Connect the waste hose from the waste lid to the drain plug
adaptor.
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 12-13-27Page 349 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(2) Do the steps (1)(a) thru (1)(q) and fill the:
-
flap actuator No.2 6211CM(6261CM)
-
flap actuator No.3 6221CM(6271CM)
-flap actuator No.4 6233CM(6283CM).
Subtask 12-13-27-612-062
B. To Remove Unwanted Semi-fluid From the Flap Actuators:
-
flap actuator No.1 6205CM(6255CM)
-
flap actuator No.2 6211CM(6261CM)
-
flap actuator No.3 6221CM(6271CM)
-flap actuator No.4 6233CM(6283CM) R **ON A/C 062-099, 106-149, 151-199, 204-299, 401-499,
(Ref. Fig. 305/TASK 12-13-27-991-005)
**ON A/C 301-399,
(Ref. Fig. 305A/TASK 12-13-27-991-005-A) R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
(Ref. Fig. 306/TASK 12-13-27-991-006)
(1)
Operate the flaps through their full range of travel five times (Ref. TASK 27-50-00-866-011) and (Ref. TASK 27-50-00-866-012). After the last operation, make sure that the flaps are in the fully extended position.
(2)
Remove unwanted semi-fluid from the flap actuator No.1 6205CM(6255CM) as follows:
(a)
Remove the vent plug (1) from the flap actuator.
(b)
Remove the drain plug (2) from the flap actuator. NOTE : The drain plug (2) is at the bottom location on the
____
actuator.
(c)
Install the vent plug adaptor 3/8 UNF (A663159) in the vent plug hole of the flap actuator.
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 12-13-27Page 350 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(d)
Install the drain plug adaptor 3/8 UNF (A663159) in the drain plug hole of the flap actuator.
(e)
Connect the waste hose from the waste lid (A663130/5) to the drain plug adaptor.
(f)
Connect the empty oil gun (A663130/4) to the vent plug adaptor.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM SERVICING 1(78)
