TASK 12-12-32-611-004 Check Fluid Level of Main Landing Gear Shock Absorber WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1.
Reason for the Job
__________________
Refer to the MPD TASK: 321113-03
2.
Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
12-12-32-611-008 Hydraulic Replenishment of the MLG Two-Stage Shock Absorber
3. Job Set-up
__________
Subtask 12-12-32-941-063
A. Not applicable
4. Procedure
_________
Subtask 12-12-32-220-051
A. Check the Fluid Level of the MLG Shock Absorber R NOTE : To do a check of the MLG shock absorber fluid level, it is
____ R necessary to do a replenishment of the MLG shock absorber.
(1) Do a replenishment of the MLG shock absorber (Ref. TASK 12-12-32-611-
008). R
TASK 12-12-32-611-008
Hydraulic Replenishment of the MLG Two-Stage Shock Absorber
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES.
_______
1. Reason for the Job__________________
Self Explanatory
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific axle jack No specific standard charging equipment No specific warning notice No specific access platform 3 m (9 ft. 10 in.) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft)
1EFF : ALL 1 12-12-32Page 327 1 1 Feb 01/05R 1 1 1CES 1
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
Material No. 02-001 USA MIL-H-5606
OIL, HYDRAULICPETROLEUM FLUID (Ref. 20-31-00)
Material No. 02-004
SHOCK ABSORBER FLUID (Ref. 20-31-00)
Material No. 19-010 USA AMS 5687
LOCKWIRE STAINLESS STEEL ANNEALED 0.8MM DIA
(Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
R 5 packing 32-11-13 01A-015 5 packing 32-11-13 01E-015 5 packing 32-11-13 01F-015 5 packing 32-11-13 01G-015
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
07-11-00-581-001 Lifting for Aircraft Maintenance Operations 07-11-00-586-002 Lowering of the Aircraft for Maintenance Operations 12-14-32-200-001 Inspection of the MLG Shock Absorbers Before Flight 12-14-32-614-003 Check Charge Pressure of Main Landing Gear Shock
Absorber 32-00-00-481-001 Installation of the Safety Devices on the Landing
Gears
12-12-32-991-009 Fig. 305
12-12-32-991-008 Fig. 306
3. Job Set-up
__________
Subtask 12-12-32-941-068
A. Safety Precautions
(1)
Make sure that the ground safety locks are installed on the landing gear (Ref. TASK 32-00-00-481-001).
(2)
On panel 400VU:
-make sure that the landing-gear control-lever 6GA is in the DOWN position
-put a warning notice in position to tell persons not to operate the landing gear.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM SERVICING 1(56)
