-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 236142-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
R No specific safety barriers
R No specific warning notice
R No specific Megohmmeter 500 Mohms - 500 VDC,1 mA max No specific adjustable access platform 11.75 m (38 ft. 7 in.)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
20-28-00-869-002 Table of the Maximum Permitted Resistance Values 23-61-00-991-001 Fig. 601
1EFF : ALL 1 23-61-00Page 601 1 1 Nov 01/99 1 1 1CES 1 1EFF : ALL 1 23-61-00Page 602 1 1 Nov 01/99 1 1 1CES 1
3. Job Set-up__________
(Ref. Fig. 601/TASK 23-61-00-991-001)
Subtask 23-61-00-941-050
A. Safety Precautions
(1) Put the safety barriers in position.
R R (2) Put the adjustable access platform in position below the applicable zone.
R R R (3) Put a warning notice in position to tell persons not to operate the flight controls.
4. Procedure_________
(Ref. Fig. 601/TASK 23-61-00-991-001)
Subtask 23-61-00-210-050
A. Inspection of the Static Dischargers
(1) Examine the static dischargers to make sure that: - there is no distortion - there is no damage to the covers - there is no corrosion of the bases - there is no damage to the tips - the screws are tight and serviceable - they are correctly attached.
Subtask 23-61-00-750-051
B. Bonding Resistance
(1) Static Discharger Retainer to Aircraft Structure.
(a) Make sure that the bonding resistance is correct (Ref. TASK 20-28-00-869-002).
Static Dischargers.
Figure 601/TASK 23-61-00-991-001
1EFF : ALL 1 23-61-00 Page 603
1 1 Feb 01/98
1 1
1CES 1
(2) Static Discharger Tip to Static Discharger Retainer.
R (a) Use a Megohmmeter 500 Mohms - 500 VDC,1 mA max to measure the resistance between the tip of the static discharger and the static discharger retainer as follows: - connect one probe to the tip of the applicable static discharger - put the other probe against the side of the applicable static discharger retainer.
R R NOTE : With one lead attached to the retainer, clip the other____ lead to a piece of WET sponge or fine wire wool (used to touch the tip of the discharger).
(b) Measure the resistance values that follow: - for type 'A', between 6 and 120 Megohms - for type 'B', between 6 and 200 Megohms.
NOTE : The resistance value for all type 'B' retainers is the____ same.
5. Close-up________
R
Subtask 23-61-00-942-050
R A. Removal of Equipment
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Remove the safety barriers.
(3) Remove the access platform(s).
(4) Remove the warning notice(s).
(5) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 23-61-00Page 604 1 1 Nov 01/99 1 1 1CES 1
DISCHARGER - STATIC - REMOVAL/INSTALLATION
__________________________________________ TASK 23-61-41-000-001 Removal of the Static Discharger WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1.
Reason for the Job
__________________
Self Explanatory
2.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM Communications 通訊3(7)
