(1) System Status The SYSTEM STATUS mode monitors the current status of the CIDS. This includes the directors, the DEUs, the data buses, the CAM, the FWD ATTND PANEL, the PTP and the interfaces to other systems. The DOOR STS menu is selected to display the status of the A/C doors (close or open). The SLIDES STS menu is to display the status of the A/C slides (armed or disarmed). For detailed failure description the MAINTENANCE mode, which is part of the SYSTEM STATUS mode, is selected.
For use by the maintenance/cabin crew, the status of the following systems is also monitored:
-Lavatory Smoke Detection
-Slides Bottle Pressure
1EFF : 001-049, 051-099, 101-105, 151-199, 1 23-73-00Page A55 1201-299, 1Config-1 Aug 01/05R 1 1 1CES 1
SYSTEM STATUS - Example
Figure 043 (SHEET 1)
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 23-73-00Page A56 1201-210, 1Config-1 May 01/05 1 1 1CES 1
SYSTEM STATUS - Example
Figure 043 (SHEET 2)
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 23-73-00Page A57 1201-210, 1Config-1 May 01/05 1 1 1CES 1
SYSTEM STATUS - Example
Figure 043A (SHEET 1)
1EFF : 211-299, 1 23-73-00Page A58 1 1 Config-1 May 01/05R 1 1 1CES 1
SYSTEM STATUS - Example
Figure 043A (SHEET 2)
1EFF : 211-299, 1 23-73-00Page A59 1 1 Config-1 May 01/05R 1 1 1CES 1
**ON A/C 001-049, 051-099, 101-105, 151-199, 201-299,
-Drainmasts
After selection of SYSTEM STATUS mode, when there are no failures,
the following messages are displayed on the PTP:
-CIDS OK
-LAV SMOKE DATA OK
-SLIDES PRESS OK
-DRAINMASTS OK
A failure in one of these systems causes an annunciation. (Ref. Para.
9E).
The SYSTEM STATUS mode is displayed automatically on the PTP, except
when the PTP is in the MAINTENANCE, the SYSTEM TEST or the
PROGRAMMING mode. The sequence of the messages in this case is
variable, the last received failure is indicated first. Any change of
the status (e.g. a failure disappears) initiates a return to the
first SYSTEM STATUS menu except when the MAINTENANCE, the SYSTEM TEST
or the PROGRAMMING mode is selected.
In case of failure the respective following messages are:
-<CIDS FAIL or <CIDS DEGRADATION
-<LAV SMOKE SYS FAIL
-<SLIDES PRESS LOW
-<DRAINMASTS FAIL For detailed information about the failure, push the related membrane switch.
(2) Detailed Messages
(Ref. Fig. 044, 045)
(a)
Messages in case of <CIDS FAIL:
-
CHECK CIDS FUNCTIONS
-
CHECK CIDS FUNCTIONS AT ATTND STATIONS Priority The first CIDS FAIL message has priority over the second, which has priority over the CIDS DEGRADATION messages. Higher priority messages inhibit the display of lower priority messages.
(b)
Messages in case of <CIDS DEGRADATION:
-
CHECK CIDS FUNCTIONS LAV X (example, the respective lavatory is shown)
-
CHECK CIDS FUNCTIONS ATT FWD L (example, the respective attendant station is shown)
-
CHECK CIDS FUNCTIONS
1EFF : 001-049, 051-099, 101-105, 151-199, 1 23-73-00Page A60 1201-299, 1Config-1 Aug 01/05R 1 1 1CES 1
SR 02 L (example, the respective seatrow is shown)
-
CHECK FWD ATTND PANEL
-
CHECK PROG & TEST PANEL
-DON'T USE PROGRAMMING MODE
(c)
Messages in case of <LAV SMOKE SYS FAIL:
-SMOKE DET FAIL LAV X (example, the respective lavatory is shown)
-NO DATA AVAILABLE
(d)
Messages in case of <SLIDES PRESS LOW:
-CHECK SLIDES PRESS FWD L (example, the location of the respective slide is shown)
(e)
Messages in case of <DRAINMASTS FAIL:
-CHECK WASTE WATER OVERFLOW FWD (example, the respective location is shown)
-MAINTENANCE
CHECK AFT CARGO DRAINAGE
**ON A/C 211-299,
(f) The DOORS-CLOSED/SLIDES-ARMED status indication (Ref. Fig. 046, 047) The doors-closed/slides-armed status is received from the SDAC and indicated on the PTP in the SYSTEM STATUS mode. The SLIDES STATUS and DOORS STATUS page must be selected manually. The displayed status is updated automatically. It will not be disturbed or interrupted by other incoming system status information. A respective OPEN or DISARMED indication is flashing. A CLOSED or ARMED indication is a steady on. Messages in case of SLIDES STATUS:
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM Communications 通訊3(72)
