R  (5) Make sure that an access platform is in position at the engine. 
R  (6) Make sure that the thrust reverser system is unserviceable (Ref. TASK 
R  78-30-00-040-040). 
R  (7) Make sure that the left fan-cowl door 447AL is open (Ref. TASK 71-13-
R  00-010-040). 
R  Subtask 29-13-35-941-053-A 
R  B. Safety Precautions 
R  (1) On the ENG panel 115VU: 
R  - make sure that the ENG 2 switch is in the OFF position 
R  - make sure that the warning notice is in position to tell persons 
R  not to start the engine. 
R  (2) Make sure that the engine 2 shutdown occurred not less than 5 minutes 
R  before you do this procedure. 
R  (3) Make sure that the warning notice is in position to tell persons not 
R  to pressurize the Yellow hydraulic system: 
R  - on the HYD section of the panel 40VU. 
R  (4) On the ENG section of the panel 50VU: 
R  - make sure that the ON legend of the ENG/FADEC/GND/PWR 2 pushbutton 
R  switch is off 
R  - make sure that the warning notice is in position to tell persons 
R  not to energize the FADEC system. 
R  (5) Make sure that a container is in position. 
R  (6) Make sure that a cloth is in position below the pipe (4).
 4. Procedure_________
 (Ref. Fig. 401/TASK 29-13-35-991-001)
 Subtask 29-13-35-420-051
 A. Installation of the Check Valve
 (1) Apply HYDRAULIC FLUIDS (Material No. 02-003) on the new O-ring (2). 
R  (2) Install the O-ring (2) on the check valve (3) (Ref. TASK 20-29-00-
911-002).

 (3)
 Remove the blanking plug from the panel (1).

 (4)
 Install the check valve (3) on the panel (1).

R (5) TORQUE the check valve (3) to between 9.7 and 10.7 m.daN (71.53 and R 78.90 lbf.ft).
 (6)
 Remove the blanking plug from the pipe (4).

 (7)
 Connect the pipe (4) to the check valve (3).

 (8)
 TORQUE the coupling nut of the pipe (4) to between 7.5 and 8.3 m.daN

 (55.30
 and 61.20 lbf.ft).
 Subtask 29-13-35-942-052-A

 B.
 Preparation for the Test

 (1)
 Remove the cloth.

 (2)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (3)
 Pressurize the Yellow hydraulic reservoir (Ref. TASK 29-14-00-614-002).

 (4)
 Make the thrust reverser system serviceable (Ref. TASK 78-30-00-440-040).

 Subtask 29-13-35-710-050-A
 C. Operational Test
 (1)
 Do the operational test of the thrust reverser system (Ref. TASK 78-31-00-710-042).

 (2)
 Make sure that there are no leaks from the connections of the check valve (3).

 (3)
 Make sure that the level of hydraulic fluid in the Yellow reservoir is correct. If necessary fill the reservoir (Ref. TASK 12-12-29-611-001).

 5. Close-up
________
 Subtask 29-13-35-410-050-A

 A. Close Access
 (1)
 Remove the warning notice(s).

 (2)
 Remove the access platform(s).

 (3)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (4) Close the left fan-cowl door 447AL (Ref. TASK 71-13-00-410-040). R

 CHECK VALVE - ENGINE 2 PUMP DELIVERY (3050GM) - REMOVAL/INSTALLATION
____________________________________________________________________ TASK 29-13-36-000-001 Removal of the Engine 2 Yellow Hydraulic Pump Delivery Check Valve (3050GM). WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES.
_______
 WARNING : DO NOT TOUCH THE HYDRAULIC SYSTEM COMPONENTS FOR A SHORT TIME AFTER

_______ THE ENGINE IS SHUTDOWN. THE ENGINE COMPONENTS STAY HOT FOR SOME TIME AND CAN CAUSE INJURY.
 CAUTION : DO NOT LET HYDRAULIC FLUID FALL ON THE ENGINE. UNWANTED HYDRAULIC
_______ FLUID MUST BE REMOVED IMMEDIATELY WITH A CLEAN LINT FREE CLOTH. THE FLUID CAN CAUSE DAMAGE TO THE SURFACE PROTECTION AND TO SOME PARTS.
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM HYDRAULIC POWER 液壓4(23)