-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1.
Reason for the Job
__________________
To make a visual inspection of the fire valve 3046GD.
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notice
No specific access platform 3 m (9 ft. 10 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-13-52-991-003 Fig. 601 3. Job Set-up
__________ (Ref. Fig. 601/TASK 29-13-52-991-003) Subtask 29-13-52-941-055
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put a warning notice in position to tell persons not to pressurize the hydraulic systems.
Subtask 29-13-52-865-053
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU HYD/FIRE VALVE/Y/ENG2 3702GD C14 121VU HYDRAULIC/Y HYD/PUMP ENG2/MONG 3700GD Q37
Subtask 29-13-52-010-052
C. Get Access
(1)
Put the access platform below zone 674.
(2)
Remove the access panel 674AB.
4. Procedure
_________ Subtask 29-13-52-210-052
A. Inspection of the Engine Pump Fire-Valve
(1)
Examine the engine pump fire-valve 3046GD for damage, corrosion and signs of leakage.
(2)
Make an inspection of the line end fittings and electrical connector, make sure they are correct and satisfactory.
Engine Pump Fire-Valve (3046GD)
Figure 601/TASK 29-13-52-991-003
1EFF : ALL 1 29-13-52 Page 603
1 1 Feb 01/98
1 1
1CES 1
5. Close-up
________ Subtask 29-13-52-410-051
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the access panel 674AB. Subtask 29-13-52-865-054
B.
Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 3700GD, 3702GD.
Subtask 29-13-52-942-052
C. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
GROUND CONNECTOR - SELF-SEALING - REMOVAL/INSTALLATION
______________________________________________________ TASK 29-13-63-000-001 Removal of the Self-Sealing Ground Connectors of the Yellow Hydraulic System WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES.
_______
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking plugs
No specific warning notice
No specific access platform 1.75 m (5 ft. 9 in.)
No specific container 5.0 l (1.3208 USgal)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
Configuration before Maintenance Action 29-00-00-910-002 Safety Procedures of the Hydraulic System 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 29-13-63-991-001 Fig. 401
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM HYDRAULIC POWER 液壓4(99)
