(7)
 Connect the upper case drain hose/tube (15) to the union (20) on the filter assembly (30).

 (8)
 TORQUE the coupling nut on the upper case drain hose (15) to between

 2.42 and 2.76 m.daN (17.84 and 20.35 lbf.ft).
 NOTE : Use a second wrench to hold the union (20) when you TORQUE the

____
 coupling nut.

R (9) Put the bulkhead nut (35) and the new (25) on the elbow (40).
 (10) Install the elbow (40) on the filter assembly (30), as follows:
 (a) Turn the elbow until the packing (25) is against the filter assembly (30).
 NOTE : The elbow must point forward and be in the horizontal
____
 position.

 (b)
 Turn the bulkhead nut (35) until it is against the filter assembly (30).

 (c)
 TORQUE the bulkhead nut (35) to between 2.03 and 2.26 m.daN

 (14.97 and 16.66 lbf.ft).
 NOTE : Use a second wrench to hold the elbow (40) when you TORQUE

____
 the bulkhead nut (35).

 (11)
 Attach the lower case drain hose (45) to the elbow (40).

 (12)
 TORQUE the coupling nut on the lower case drain hose (45) to between

 2.42 and 2.76 m.daN (17.84 and 20.35 lbf.ft).
 NOTE : Use a second wrench to hold the elbow (40) when you TORQUE the

____
 coupling nut on the hose.

 Subtask 29-13-43-710-052
 B. Operational Test
 (1)
 Pressurize the Yellow hydraulic reservoir (Ref. TASK 29-14-00-614-002).

 (2)
 Pressurize the Yellow hydraulic system (Ref. TASK 29-23-00-863-002).

 (3)
 Do an operational test of the Yellow hydraulic system (Ref. TASK 29-13-00-710-002).

 (4)
 During the dry motoring of the engine 2, make sure that:

 -there are no leaks from the case drain filter,
 -the clogging indicator of the filter is not out.

 (5)
 Stop the dry motoring of the engine 2.

 5. Close-up
________
 Subtask 29-13-43-410-053

 A. Close Access
 (1)
 Remove the warning notice(s).

 (2)
 Remove the access platform(s).

 (3)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (4)
 Close the left fan cowl door

 FOR 1000EM2 R close the door 447AL (Ref. TASK 71-13-00-410-040).
 (5) Close the door 195BB.

 FILTER - LP (3002GM) - SERVICING
________________________________
 TASK 29-13-44-610-001
 Servicing of the LP-Filter (3002GM)
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
_______
 CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.

 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE  QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
 No specific warning notices
 No specific container 3.0 l (0.7925 USgal)

 B. Consumable Materials
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
No specific  lockwire 0.8 mm (0.032 in.)
R  Material No. 02-003 F NSA 307110 TYPE 4 HYDRAULIC FLUID (PHOSPHATE ESTER BASE) (Ref. 20-31-00)
 C. Expendable Parts
 -------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION  |IPC-CSN
 -------------------------------------------------------------------------------
2 O-ring 29-13-44 01 -020 4 filter element 29-13-44 01 -030 D. Referenced Information

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
12-12-29-611-001 Fill the Hydraulic Fluid Reservoir with a Hand Pump 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM HYDRAULIC POWER 液壓4(53)