U1 = U(Final)(plus or minus 10mV) If the value is not in the limits, do the procedure from stage 4 again.

 (19)
 Remove the RVDT 3GC (16) (Ref. TASK 32-51-19-000-001).

 (20)
 Tighten the screws (11) through elongated holes of the ADJUSTING TOOL

 -NWS GEARBOX (13).
 1EFF : 001-004, 051-054, 1 32-51-00Page A538 1 1 Aug 01/05R 1 1 1CES 1

 (21)
 Loosen the knurled adjusters (14).

 (22)
 Remove the ADJUSTING TOOL - NWS GEARBOX (13).

 (23)
 Install the RVDT 3GC (16) (Ref. TASK 32-51-19-400-001).

 (24)
 Do a check for the integrity of the adjustment:

 (a)
 On the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST

 (18) set the selector switch to U1.

 (b)
 Record the voltage.

 (c)
 On the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST

 (18) set the selector switch to U2.

 (d)
 Record the voltage.

 (e)
 Make sure that:

 U1 = U2 plus or minus 20mV. If the value is not in the limits, do the procedure from step (2) again.
 (25)
 On the panel 402VU, put the A/SKID & N/W STRG switch in OFF position.

 (26)
 Remove the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST (18).

 (27)
 Connect the electrical connector (19) to the RVDT 3GC (16).

 (28)
 Do the procedure again for the RVDT 4GC (monitor channel).

 (29) On the panel 402VU, put the A/SKID & N/W STRG switch in ON position. Subtask 32-51-00-865-104
 C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 3GG, 4GG, 2EN1, 2EN2
R 1EFF : 001-004, 051-054, 1 32-51-00Page A539 1 1 Aug 01/05 1 1 1CES 1

 5. Close-up
________ Subtask 32-51-00-860-076
 A. Aircraft Maintenance Configuration
 (1)
 Lower the aircraft on its wheels and move the axle jack away .

 (2)
 Move the aircraft to remove the grease plates (Ref. TASK 09-10-00-584-002).

 Subtask 32-51-00-740-058
 B. Bite Test
 (1) Do the Bite test of the BSCU (Ref. TASK 32-46-00-740-001). Subtask 32-51-00-942-065
 C. Remove the Equipment
 (1)
 Remove the Nose Wheel Alignment Tool

 (2)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (3)
 Remove the access platform(s).

 (4)
 Remove the warning notice(s).

 (5)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

R 1EFF : 001-004, 051-054, 1 32-51-00Page A540 1 1 Aug 01/05 1 1 1CES 1 TASK 32-51-00-820-003- 01

 Adjustment of the NWS "Zero" Position with Adjusting Tool M46196 for A/C with NWS Sensor (3GC, 4GC) P/N C24763000 using the Nose Wheel Alignment Tool
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1. Reason for the Job
__________________
R Do this procedure when you adjust a gear box P/N C24764000 with the tool R M46196 using the Nose Wheel Alignment Tool for the adjustment. R
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
 No specific warning placard
 No specific AC voltmeter
 No specific square steel plates 1.2 m (3 ft. 11 in.)
 No specific Torque Wrench : range 0.00 to 1.20 m.daN

 (0.00 to 9.00 lbf.ft)
 F26792000 1 SENSOR-VOLTAGE TEST
 F26792000-1 1 SENSOR - VOLTAGE TEST
 JT2000AIRBUS 1 NOSE WHEEL ALIGNMENT TOOL
 M46196 1 ASSEMBLY TOOL
 98A09003000001 1 BAR - STEERING NOSE WHEEL

R 1EFF : 001-004, 051-054, 1 32-51-00Page A541 1 1 Aug 01/05 1 1 1CES 1

 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架9(22)