R 1EFF : 001-004, 051-054, 1 32-51-00Page A542 1 1 Aug 01/05 1 1 1CES 1
3. Job Set-up
__________
Subtask 32-51-00-941-060
A. General
(1) Put a warning placard in the cockpit to tell persons not to operate R the landing gear or the N/WS.
(2)
On the panel 400VU, make sure that the L/G normal control lever is in the DOWN position and the A/SKID & N/W STRG switch is ON.
(3)
On the nose gear leg, on the nose wheel steering deactivation electrical box, make sure that the towing lever is in the normal position (engaged position).
(4)
Make sure that the N/WS handwheels and the rudder pedals are in the neutral position.
(5) Make sure that RUD TRIM indicator shows 0.
Subtask 32-51-00-860-079
B. Aircraft Maintenance Configuration
(1) Move the aircraft and position the nosewheels on the square steel plates
(a)
Position a steel plate in front of the wheels
(b)
Apply a thick layer of COMMON GREASE (Material No. 04-004) to the upper surface of the steel plate
(c)
Put the other steel plate on the top of the greased steel plate
(d)
Move the aircraft and position the nose wheels on the greased steel plates (Ref. TASK 09-10-00-584-002)
1EFF : 001-004, 051-054, 1 32-51-00Page A543 1 1 Aug 01/05 1 1 1CES 1
(2) Installation of the NOSE WHEEL ALIGNMENT TOOL (JT2000AIRBUS) (Ref. Fig. 520/TASK 32-51-00-991-022, 521/TASK 32-51-00-991-039, 522/TASK 32-51-00-991-040)
WARNING : BE CAREFUL WHEN YOU USE THIS TOOL, BECAUSE IT CONTAINS
_______
CLASS 2 LASER EQUIPMENT.
-
DO NOT LOOK DIRECTLY INTO THE BEAM
-
DO NOT POINT THE BEAM AT OTHER PERSONS. THE LASER CAN CAUSE INJURY IF YOU DO NOT OBEY THESE PRECAUTIONS.
(a)
Open the radome to get access to the reference point (first point) (Ref. TASK 53-15-11-010-001)
(b)
Do a mark on the NLG doors (second point)
NOTE : These two reference points will be used to set-up the
____
front target
(c) Make sure that the area under the center and rear sections of the fuselage is clear
-identify the reference points (11) and (12) under the fuserlage (Ref. TASK 08-22-00-200-001)
-install the target on the refence point (12)
NOTE : These two reference points will be used to set-up the rear
____
target
(d)
Jack up the NLG axle enough to spin the two wheels (Ref. TASK 07-12-00-582-001)
(e)
Refer to the manufacturer's instruction manual to install and set-up the Nose Wheel Alignment Tool
(f)
Lower the aircraft on its wheels and move the axle jack away
(3)
Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002)
(4)
Make sure that rhe N/WS handwheels and the rudder pedals are in the neutral position
(5)
Pressurize the Green hydraulic system (Ref. TASK 29-10-00-863-001)
(6)
Set the rudder trim to zero position.
1EFF : 001-004, 051-054, 1 32-51-00Page A544 1 1 Aug 01/05R 1 1 1CES 1
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架9(23)
