(d)
 Record the voltage (U2).

 (e)
 From the voltages U1 and U2, calculate the voltage U: U = U1 - U2

R 1EFF : 001-004, 051-054, 1 32-51-00Page A553 1 1 Aug 01/05 1 1 1CES 1

 (9) If the voltage U is not equal to 0 +/- 20mV, adjust the gear box:
 (a)
 Remove the RVDT 3GC (1) (Ref. TASK 32-51-19-000-001).

 (b)
 Install the ASSEMBLY TOOL (M46196) on the gearbox, put the stud

 (15) of the rigging tool M46196-2 (14) in the drive slot (13) of the gearbox plate (11).

 (c)
 Hold the rigging tool M46196-2 (14) in position and loosen the screws (12).

 (d)
 Lightly move the gearbox plate (11) with the rigging tool M46196-2 (14):.

 -clockwise if the value U is less than minus 20mV
 -counterclochwise if the value U is more than plus 20mV

 (e)
 TORQUE the screws (12) to between 0.1 and 0.15 m.daN (8.84 and

 13.27 lbf.in).
 NOTE : Make sure that the gearbox plate (11) does not move when

____ you TORQUE the screws (12). If the gearbox plate (11) moves, the adjustment will not be correct.
 (f)
 Remove the rigging tool M46196-2 (14).

 (g)
 Install the RVDT 3GC (1) (Ref. TASK 32-51-19-400-001). NOTE : Lightly lubricate the packing of the sensor 3GC with

____
 COMMON GREASE (Material No. 04-015).

 (h)
 On panel 402VU, put the A/SKID & N/W STRG switch in ON position.

 (10) Stage 2:
 (a)
 On the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST

 (2) set the selector switch to U1.

 (b)
 Record the voltage (U1*)(in AC voltage).

 (c)
 On the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST

 (2) set the selector switch to U2.

 (d)
 Record the voltage (U2*)(in AC voltage).

 (e)
 Calculate the algebraic value U*:
 (U1* - U2*) = U*

R 1EFF : 001-004, 051-054, 1 32-51-00Page A554 1 1 Aug 01/05 1 1 1CES 1

 (f)
 Check that the algebraic value U*:
 U* = 0 +/- 20 mV

 (g)
 If U* is not in the tolerance do the procedure from step (2) again.

 (11)
 On the panel 402VU, put the A/SKID & N/W STRG switch in OFF position.

 (12)
 Remove the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST (2).

 (13)
 Connect the electrical connector (3) to the RVDT 3GC (1).

 (14)
 Do the procedure again for the RVDT 4GC (monitor channel).

 (15) On the panel 402VU, put the A/SKID & N/W STRG switch in ON position. Subtask 32-51-00-865-110
 C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 3GG, 4GG, 2EN1, 2EN2
 5. Close-up
________ Subtask 32-51-00-860-080
 A. Aircraft Maintenance Configuration
 (1)
 Lower the aircraft on its wheels and move the axle jack away.

 (2)
 Move the aircraft to remove the grease plates (Ref. TASK 09-10-00-584-002).

 Subtask 32-51-00-740-060
 B. Bite Test
 (1) Do the Bite test of the BSCU (Ref. TASK 32-46-00-740-001).
R 1EFF : 001-004, 051-054, 1 32-51-00Page A555 1 1 Aug 01/05 1 1 1CES 1 Subtask 32-51-00-942-067

 C. Remove the Equipment
 (1)
 Remove the Nose Wheel Alignment Tool

 (2)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (3)
 Remove the access platform(s).

 (4)
 Remove the warning notice(s).

 (5)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

R 1EFF : 001-004, 051-054, 1 32-51-00Page A556 1 1 Aug 01/05 1 1 1CES 1R **ON A/C 005-049, 055-099, 101-149, 151-199, 201-299, 301-399, 401-499,

 TASK 32-51-00-820-003-A
 Adjustment of the NWS "Zero" Position for A/C with NWS Sensor Box (3GC, 4GC) P/N E21336000 using the Nose Wheel Alignment Tool
 CAUTION : IF THE SENSOR BOX HAS P/N E21336000, NEVER REMOVE THE SENSOR FROM THE
_______ GEARBOX. THE SENSOR AND THE GEARBOX ARE AN ASSEMBLY THAT YOU MUST NOT DISASSEMBLE ON THE AIRCRAFT. IF YOU REMOVE THE SENSOR FROM THE GEARBOX:
 -YOU WILL CAUSE DAMAGE TO THE SENSOR BOX
 -THE ADJUSTMENT OF THE SENSOR BOX WILL NO LONGER BE CORRECT.
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架9(25)