NOTE : Do not mix Material No. 04-004 with Material No. 04-022.
____ You can use Material No. 04-022 as an alternative to Material No. 04-004. Clean and degrease the parts before you use Material No. 04-022.
(c)
Put the other steel plate on the top of the greased steel plate
(d)
Move the aircraft and position the nosewheels on the greased steel plates (Ref. TASK 09-10-00-584-002)
(2) Installation of the NOSE WHEEL ALIGNMENT TOOL (JT2000AIRBUS) WARNING : BE CAREFUL WHEN YOU USE THIS TOOL, BECAUSE IT CONTAINS
_______
CLASS 2 LASER EQUIPMENT.
-
DO NOT LOOK DIRECTLY INTO THE BEAM
-
DO NOT POINT THE BEAM AT OTHER PERSONS. THE LASER CAN CAUSE INJURY IF YOU DO NOT OBEY THESE PRECAUTIONS.
(Ref. Fig. 602/TASK 32-51-00-991-033)
**ON A/C 001-049, 051-099, 101-149, 151-199, 201-299,
(Ref. Fig. 603/TASK 32-51-00-991-034) **ON A/C 301-399,
(Ref. Fig. 603A/TASK 32-51-00-991-034-A)
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-51-00Page 604 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1
Nose Wheel Alignment Tool - Location and Detail Figure 601/TASK 32-51-00-991-031
1EFF : 1 1R 1CES ALL 1 11 1 32-51-00 Page 605 Aug 01/05
Reference points for the front target Figure 602/TASK 32-51-00-991-033
R 1EFF : 1 1 1CES ALL 1 111 32-51-00 Page 606 Aug 01/04
Reference points for the rear target
Figure 603/TASK 32-51-00-991-034
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-51-00Page 607 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
R Reference points for the rear target
R Figure 603A/TASK 32-51-00-991-034-A
R 1EFF : 301-399, 1 32-51-00 Page 608
1 1 May 01/04
1 1
1CES 1
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
(a)
Open the radome to get access to the reference point (Ref. TASK 53-15-11-010-001) (first point)
(b)
Do a mark on the NLG doors (second point)
NOTE : These two reference points will be used to set-up the
____
front target
(c) Make sure that the area under the center and rear sections of the fuselage is clear
-identify the reference points (11) and (12) under the fuselage (Ref. TASK 08-22-00-200-001)
-install the target on the reference point (12)
NOTE : These two reference points will be used to set-up the rear
____
target
(d)
Jack up the NLG axle enough to spin the two wheels (Ref. TASK 07-12-00-582-001)
(e)
Refer to the manufacturer's instruction manual to install and set-up the Nose Wheel Alignment Tool
(f)
Lower the aircraft on its wheels and move the axle jack away
(3)
Energize the aircraft electrical circuits
(Ref. TASK 24-41-00-861-002).
(4)
Make sure that the N/WS handwheels and the rudder pedals are in the neutral position
(5)
Pressurize the Green hydraulic system
(Ref. TASK 29-10-00-863-001).
(6)
Set the rudder trim to zero position.
(7)
Close the circuit breakers 1GG,2GG,3GG and 4GG and open the circuit breakers 2EN1 and 2EN2
(8)
Jack up the NLG axle enough to spin the two wheels (Ref. TASK 07-12-00-582-001)
-put a thick layer of COMMON GREASE (Material No. 04-004) and COMMON GREASE (Material No. 04-022) on the pivoting cup of the axle jack
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-51-00Page 609 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1 1EFF : ALL 1 32-51-00Page 610 1 1 Aug 01/05 1 1 1CES 1 1EFF : 401-499, 1 32-51-00Page 611 1 1 Aug 01/05 1 1 1CES 1R **ON A/C ALL
NOTE : Do not mix material 04-004 with material 04-022. You can use____
material 04-022 as an alternative to material 04-004. Clean
and degrease the parts beforeyou use material 04-022.
- Jack up the NLG axle enough to spin the two wheels
R **ON A/C 401-499,
R Subtask 32-51-00-860-081-A
R D. Aircraft Maintenance Configuration
R (Ref. Fig. 601/TASK 32-51-00-991-031)
R (1) Move the aircraft and position the nosewheels on the two
R 1.2m(4ft.)square steel plates
R (a) Position a steel plate in front of the nosewheels
R (b) Apply a thick layer of COMMON GREASE (Material No. 04-004) or
R COMMON GREASE (Material No. 04-022) to the upper surface of the
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架9(31)
